Actualizaciones De La Riff Box Solo Aqui Opciones

[dapx]

RIFF JTAG – Samsung SCH-i920 Omnia II 8GB Unbrick – Dead Boot repair supported

by admin on Mar.31, 2012, under News

RIFF JTAG – Samsung SCH-i920 Omnia II 8GB Unbrick – Dead Boot repair supported

Repairing bricked Samsung I920 AP (PDA Part) is easy with RIFF Box. Due to some hardware pecularities, we recommend to use only battery without USB cable connected. Please note, during connection establishment phase you will have to press the Power On key twice.

To resurrect Samsung I920 AP:

Solder JTAG cable to Samsung I920 AP JTAG pads;
Make sure Samsung I920 AP is selected in the list of models;
Insert battery; make sure no USB cable or charger is connected;
Press the Power On key;
Click Resurrect button;
When it stops at “Establish communication with the phone…” press the Power On key again;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

To resurrect Samsung I920 CP:

Solder JTAG cable to Samsung I920 CP JTAG pads;
Make sure Samsung I920 CP is selected in the list of models;
Insert battery and connect USB cable or charger;
Wait till AP part boots up completely;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.



RIFF JTAG – Samsung SHV-E120S Galaxy S II HD LTE (Samsung Celox) Unbrick – Dead Boot Repair supported

by admin on Mar.31, 2012, under News

RIFF JTAG – Samsung SHV-E120S Galaxy S II HD LTE (Samsung Celox) Unbrick – Dead Boot Repair supported

Repairing bricked Samsung E120S is easy with the RIFF Box. The device is based on the 2nd-generation Qualcomm MSM8660 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung E120S:

Solder JTAG cable to Samsung E120S JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung E120S is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press Power-On.


Saludos. Enjoy

[Anunciante Autorizado]

[miguelpaolo]

03.04.2012 RIFF JTAG – Samsung Galaxy Mini – GT-S5570i Unbrick – Boot repair supported
Repairing bricked Samsung S5570i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5570i:

• Solder JTAG cable to Samsung S5570i JTAG pads;
• Connect USB cable to phone and PC;
• Insert battery;
• Make sure Samsung S5570i is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
• If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.

.

[jorcomax11]

RIFF JTAG – Samsung Galaxy Ace – GT-S5830i Unbrick – Boot Repair supported

by admin on Apr.03, 2012, under News

03.04.2012 RIFF JTAG – Samsung GT-S5830i Unbrick – Boot Repair supported

Repairing bricked Samsung GT-S5830i is easy with RIFF Box. To power the phone connect USB cable and insert battery. Sometimes it’s needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S5830i:

Solder JTAG cable to Samsung S5830i JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung S5830i is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Menu’ keys and press Power-On.
If nothing happens, try an alternative: hold both ‘Volume Up’ and ‘Menu’ keys and press Power-On.
 Samsung_... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 18.29k ) Número de descargas: 0

[SpLock]

RIFF JTAG - HTC Flyer, Routers, Sat Receivers . . .

06.04.2012 RIFF JTAG Updates

Whats new:

RIFF JTAG Manager v1.42
RIFF Box Firmware v1.32

Network Router support:

LinkSys WRT54G Unbrick, Read/Write Flash

Satellite Receivers (STB-s):

Orton 4100C Unbrick, Read/Write Flash
EuroSky ES-4100 Unbrick, Read/Write Flash

HTC Phones support:

HTC Flyer Boot repair, Unlock, CID, ModelID, S-Off, IMEI Update

HTC Phones bug fix and updates:

HTC Sensation (HTC Pyramid) S-Off support added
HTC Evo 3D (HTC Shooter) S-Off support added
HTC Desire HD DBL reflash support added
HTC Desire Z DBL reflash support added

RIFF Torrent Tracker updates:

06.04.2012 HTC_Working_Full_flash_Backups_06.04.2012_v2.torre nt

New HTC Full Backups torrent is uploaded and ready for seeding.

New files for following models: HTC 7 Pro (tested with hspl)
HTC Evo 3D (for Liteon camera)
HTC Desire HD (hboot 2.00 with fix for network problem)
HTC Sensation
HTC Kaiser
HTC Surround
HTC Incredible S

Complete list of files:

06.04.2012 Samsung_Full_flash_backups_06.04.2012_v2.torrent

New files for many new models added.

www.riffbox.org
Report Post
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiShare on FacebookTwitterStumble this Post!
Reply With Quote

[dapx]

RIFF JTAG - HTC via USB cable supported

24.04.2012 RIFF JTAG – HTC via USB Cable Support added


Whats new:

Released support for HTC phones based on MSM8x55 CPU, which are enumerated on USB port as “QHUSB_DLOAD” device. Now it’s possible to repair these phones without soldering any wires. Even without opening !

Following models are supported at the moment:

HTC Desire HD (HTC Ace)
HTC Desire S (HTC Saga)
HTC Desire Z (HTC Vision)
HTC Flyer 3G
HTC Flyer WiFi
HTC Evo View 4G

It is possible to force QHUSB_DLOAD mode by disabling Vdd line on eMMC chip. Check Desire S TP info for example. This means, You can work with any MSM8255/MSM8655 based HTC phone, as long as You force it into QHUSB_DLOAD mode.
Follow this procedure if You want to use these updates:


Connect Your phone to USB port and install QHUSB_DLOAD device driver (C:\Program Files (x86)\RIFF Box JTAG Manager\Drivers\32Bit\QDLOADER)
Launch JTAG Manager, select appropriate Model DLL and click desired button
Install “RIFF Box DCCLoader USB Interface” port driver (C:\Users\Admin\Desktop\Drivers_64Bit_WorkedForMe\ Drivers\64Bit\DCCLDR)
If required, repeat the procedure (sometimes required if device is connected for first time)

We will release USB support for rest of the models on these CPU-s in following days.
To download and install new updates – simply click “Check for Updates” button on Box Service TAB.

Saludos. Enjoy

[thenshi]

RIFF JTAG - HTC via USB cable 5 more models supported
27.04.2012 RIFF JTAG – HTC via USB more phones supported

HTC Thunderbolt USB support added
HTC Sensation XL USB support added
HTC Inspire USB support added
HTC Incredible S USB support added
HTC Incredible 2 USB support added

These new updates will allow You to use USB cable to perform any operation on listed models. Remember that this work if Your phone is enumerated on USB port as QHUSB_Dload or Qualcomm HS-USB QDLoader device.
In case phone is not enumerated, You might need to use test point method first.
Please visit RIFF FAQ section in to see how to install drivers, and how to find eMMC Vdd test points:

How to install QHUSB_DLOAD driver
How to install “RIFF BOX DCCLoader USB Interface Port” Windows 7 64bit driver

If You need to repair phone after replacing eMMC chip, these are the steps:

Launch eMMC MBR/EBR partitioning tool
Open desired partitioning file
Click “Load Image from file”
Click “Repartition eMMC”
Close the eMMC plugin
Click “Resurrection” and select all options to be repaired, including IMEI and CID
Click “Resurrect”

http://www.jtagbox.com/wp-content/up...ull_repair.jpg

Please click “Check for updates” button to download and install new updates.


www.jtagbox.com

[3zr3vnoc]

RIFF JTAG-RIFF JTAG Manager v1.43 released

RIFF Box JTAG Manager software setup

This will install following files to Your computer:
JTAG Manager software v1.43
RIFF Box Firmware v1.32
RIFF Box control port driver
RIFF Box update port driver
RIFF DCC USBLoader driver
QUALCOMM QHUSB_DLOAD driver
After You execute setup, it will install all files to desired destination, and launch drivers installer script.
Take note, If You’re using Windows XP, You’ll have to provide drivers location to Hardware Installation Wizard after connecting devices for first time.

RIFF Box – JTAG Revolution

[miguelpaolo]

04.05.2012 RIFF JTAG – Samsung SGH-T679 Exhibit II 4G (Samsung Ancora) Unbrick – Dead Boot repair supported

Repairing bricked Samsung T679 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Please note, MSM8255T is multi-core chipset – it has ARM11 and Qualcomm Scorpion cores. During power on sequence only ARM11 core is visible on the JTAG chain. If boots are not completely damaged and it comes up to initializing of the Scorpion core then Scorpion core appears on the JTAG chain too. This will shift ARM11 from TAP0 into TAP1 position on the chain, while current resurrector has the ARM11 core hardcoded at TAP0 position. Thus make sure to establish JTAG connection in the time range while Scorpion core is not visible yet.

To resurrect Samsung T679:

• Solder JTAG cable to Samsung T679 JTAG pads;
• Make sure Samsung T679 is selected in the list of models;
• Insert battery and connect USB Data cable;
• If you use only battery, press Power On key;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold 'Volume Down' key and press 'Power ON' button.

.

[miguelpaolo]

11.05.2012 RIFF JTAG – Samsung SPH-D710 Galaxy S2 Epic Touch 4G (Samsung Within) Unbrick – dead boot repair supported


Repairing bricked Samsung SPH-D710 Galaxy S2 Epic Touch 4G is easy with RIFF Box. Samsung SPH-D710 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core). JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
To resurrect Samsung SPH-D710:

• Solder JTAG cable to Samsung SPH-D710 JTAG pads;
• Connect USB cable to phone and PC;
• Insert battery;
• Make sure Samsung SPH-D710 is selected in the list of models;
• Make sure a fixed TCK frequency is selected;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

.

[Eliminado_gsm_sps_*]

RIFF JTAG - Weekend Updates
18.05.2012 RIFF JTAG – Weekend updates:

Whats new:

Samsung B7320 unbrick/boot repair support added
HTC Sensation 4G (PG581000) Unbrick, Unlock, S-Off, SuperCID support added
HTC Sensation (PG581300/PG583101) Unlock support added
HTC Evo 3D Unlock support added

Bug Fix updates:

HTC Desire HD Support for new board revisions with hboot 2.xx (No Network problem)
HTC Wildfire S Proximity sensor fix

RIFF Torrent tracker:

http://www.jtagbox.com/

Mensaje modificado por gsm_sps el May 18 2012, 02:13 PM

Fichero(s) Adjunto(s)

 19_HTC_S... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 38.18k ) Número de descargas: 0

 

[miguelpaolo]

.
23.05.2012 RIFF JTAG – HTC 7 Surround T8788 (HTC Mondrian) Unbrick, Unlock, SuperCID and IMEI repair supported


Repairing bricked HTC Surround (PD26100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.74.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD26*****’.

To resurrect HTC Surround (PD26100):

• Solder JTAG cable to HTC Surround JTAG pads;
• Insert USB Data cable into board and PC;
• Make sure HTC Surround (PD26100) is selected in the list of models;
• If you use battery, press Power On key;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

[CelularPlanes]

31/05/2012 RIFF JTAG Actualizaciones Qué es lo nuevo:



HTC uno T320e (HTC Primo) unbrick / reparación del boot muerto, Desbloquear , SuperCID, reparación de IMEI , a través de cable USB, del Primer Mundo

Samsung SHV-E160K Nota Galaxy LTE de inicio de reparación / eMMC re-partición


RIFF Torrent Rastreador de actualizaciones:

RiffBox instalación v1 05/31/2012


WWW.RIFFBOX.ORG

[miguelpaolo]

12.06.2012 RIFF JTAG – HTC Rhyme (HTC Bliss) Unbrick, Unlock, SuperCID and IMEI Update via USB Supported





Repairing bricked HTC Rhyme (PI46100) is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected. Please note, battery presense is required.
Current resurrector works via USB interface thus no JTAG connection is required. You may need to install RIFF BOX DCC Loader USB Interface USB driver if you run this for the first time. Drivers are located in JTAG Manager directory (Drivers folder).
In order to connect, device must be detected by system as Qualcomm HS-USB QDLoader communication port. To force device into this mode (that is if your device is dead but there is still no USB activity when you connect it to PC with USB cable) use testpoint to disable the eMMC memory – for this shortcut specified point on the schematics to the GND during power-on stage.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.30.0004 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PI4610000’.
There is option to reflash android BOOT and RECOVERY zones.

To resurrect HTC Rhyme via USB Cable:

• If required, use testpoint to force HS-USB QDLoader mode: for this de-power board, shortcut specified point in the schematics to GND with the help of a needle, attach battery and then insert USB cable into PC, wait while phone enumerates as HS-USB QDLoader and then remove the needle;
• Make sure HTC Rhyme (PI46100) is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Depower the phone;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press ‘Power ON’ button.

.

[miguelpaolo]

15.06.2012 CDMA Updates – 4 new ZTE models

Whats new:

• ZTE S170 support added
• ZTE S180 support added
• ZTE S165 support added
• ZTE FWPC26 support added

Bug fixes:

• HTC_Flyer_PG41100.dll
• HTC_Flyer_PG41400.dll

PLL frequency is lowered, now no more RAM memory test failed bug error at the connection stage.RIFF Torrent tracker:

• RiffBox_Setup_15.06.2012_v1.torrent

[cellcentersps]

22.06.2012 RIFF JTAG Updates:

Whats new: http://www.jtagbox.com/jtag-news/riff-jtag...pair-supported/

Unbrick/Boot repair
S-Off
Unlock
IMEI Repair
SuperCid

Bug Fixes:

HTC_Sensation_PG58130.dll, HTC_EVO3D_PG86300.dll, HTC_Sensation4G_PG58100.dll
.
Fixed bug with damaged WLAN partition
Added WLAN partition check box in the resurrection settings dialog for optional WLAN zone resurrection (Use only in case when repairing erased or new eMMC)
Resurrection of mirrored-MISC partition is added (In some cases phone remain in recovery mode after failed update. This update solves this issue)

Torrent Tracker: http://tracker.riffbox.org/login.php?retur...%3Ftorrent%3D49

http://www.riffbox.org/

[miguelpaolo]

20.07.2012 RIFF JTAG -Samsung SGH-i747 Galaxy S III LTE Unbrick / Boot repair supported, World First ! ! !

Repairing bricked Samsung SGH-i747 Galaxy S III LTE is easy with the RIFF Box. The device is based on the Qualcomm MSM8960 chipset.

Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Make sure to set fixed TCK frequency. With RTCK mode selected, DCC Loader will not respond.

To resurrect Samsung I747:

• Solder JTAG cable to Samsung I747 JTAG pads;
• Connect USB cable to phone and PC;
• Insert battery;
• Make sure Samsung I747 is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press Power-On.

.

[elcorrentino25]

31.08.2012 RIFF JTAG – Fly IQ285 unbrick – boot repair supported


Repairing bricked Fly IQ285 is easy with the RIFF Box. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Resurrector reflashes radio’s boot zones. There are options to reflash BOOT and RECOVERY zones.
To resurrect Fly IQ285:
Solder JTAG cable to Fly IQ285 JTAG pads;
Insert batter and connect USB Data cable;
Make sure Fly IQ285 is selected in the list of models;
If you use only battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.

 Fly_Turb... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 23.02k ) Número de descargas: 0

.

[miguelpaolo]

10.09.2012 RIFF JTAG – Samsung SGH-A887 Unbrick – Dead boot repair



The Samsung A887 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung A887:

• Solder JTAG cable to Samsung A887 JTAG pads;
• connect USB cable;
• Make sure Samsung A887 is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both 'Volume Down' and 'Camera' keys and press 'Power ON' button.

.

[miguelpaolo]

11.09.2012 RIFF JTAG – Samsung SHV-E120L Galaxy S II HD Unbrick – Dead boot repair



Repairing bricked Samsung E120L is easy with the RIFF Box. The device is based on the 2nd-generation Qualcomm MSM8660 chipset.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.

To resurrect Samsung E120L:

• Solder JTAG cable to Samsung E120L JTAG pads;
• Connect USB cable to phone and PC;
• Insert battery;
• Make sure Samsung E120L is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press Power-On.

.

[miguelpaolo]

14.09.2012 RIFF JTAG -Huawei Ideos X1 U8180 (Huawei Gaga) Unbrick – Dead Boot repair

Resurrecting Huawei U8180 is simple with RIFF Box.
Connection can be established with charger connected while battery is inside.

To resurrect Huawei U8180:

• Solder JTAG cable to Huawei U8180 JTAG pads;
• Connect Huawei U8180 tablet's charger for power;
• Make sure Huawei U8180 is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• De-solder JTAG wires;

Now device is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold 'Volume Down' key and press 'Power ON' button.

.


:Boot Repair, Huawei, Jtag Cable, Models, Operation Completion, Pc Cable, Riff, Volume Down more...
<H2 class=topTitle>RIFF JTAG – Samsung GT-S7500L Galaxy Ace Plus Unbrick – Dead Boot repair</H2>[/color]

14.09.2012 RIFF JTAG – Samsung GT-S7500L Galaxy Ace Plus Unbrick – Dead Boot repair

Resurrecting Samsung S7500L is easy with RIFF box.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on, so no need to press any power-on buttons on the phone keypad.To resurrect Samsung S7500L:

• Solder JTAG cable to Samsung S7500L JTAG pads;
• Insert USB Data cable into board and PC;
• Make sure Samsung S7500L is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold 'Volume Down' and 'Home' keys and press Power-On.

.


:Ace, Boot Repair, Data Cable, Galaxy, Home Keys, Jtag Cable, Models, Operation Completion, Pc Cable, Power Supply, Riff, Samsung, Samsung Usb, Usb Cable more...
<H2 class=topTitle>RIFF JTAG – Samsung GT-S6102 Galaxy Y Duos Unbrick – Dead Boot repair</H2>

[color="#000000"]<script src="http://connect.xxx.net/en_US/all.js#appId=224313110927811&xfbml=1">

14.09.2012 RIFF JTAG – Samsung GT-S6102 Galaxy Y Duos Unbrick – Dead Boot repair

Resurrecting Samsung S6102 is easy with RIFF Box . To power the phone connect USB cable and insert battery. Sometimes it's needed to press Power On key.
In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.

To resurrect Samsung S6102:

• Solder JTAG cable to Samsung S6102 JTAG pads;
• Connect USB cable to phone and PC;
• Insert battery;
• Make sure Samsung S6102 is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both 'Volume Down' and 'Menu' keys and press Power-On.
• If nothing happens, try an alternative: hold both 'Volume Up' and 'Menu' keys and press Power-On.

.