Hard Reset Y Frp Cubot King Kong 8 Opciones

[tona12]

borrar y frp cubot king kong con pandora
conectar apretando vol mas y vol menos apagado
y listo 3 min y como nuevo

Selected model: Cubot KingKong 8
Operation: Erase FRP And Wipe
Software version: 9.25
Erasing of partitions can damage your device.
Make sure that you have a backup created. Continue? YES

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM_V1632 (Android),usb2ser.sys,3.0.1504.0]
Device found at COM385 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [00000000]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0788
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Get sec config... OK [00000000]
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM386 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0788
Get sec config... OK [00000000]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6771]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xBD1A1232, 0xEF52FB7F, 0x5334739E, 0xABCA33B9
Get Chip ID... [MT6771]
Get SOC ID... [C5B414E077045FFD00C8CC0CF005608F57CFCB27EF92F5BBC1D20015277EA2FD]
Get sec config... OK [00000000]
Load DownloadAgent... OK
Search DA... OK [9]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): H28S9X401CMR (A002)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : H28S9X401CMR
UFS_FWVER : A002
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x3B96000000 (238.34Gb)
RAM INFO:
INT_SRAM: 0x0000039000 (228.00Kb)
EXT_RAM : 0x0180000000 (6.00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [B]
Read product info... [EXT4] ... OK
Product Brand : CUBOT
Product Manufacturer : CUBOT
Product Model : KINGKONG 8
Product Name : KINGKONG_8_EEA
Product Device : KINGKONG_8
Product Board : CUBOT
Board Platform : mt6771
Build ID : TP1A.220624.014
Build Date : Mon May 26 17:35:00 CST 2025
Display ID : CUBOT_KINGKONG_8_D013C_V10_20250526
Security Patch : 2025-06-05
Version SDK : 33
Version Release : 13
Version Codename : REL
Firmware Version : 2025211
Userdata FS Type : EXT4
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Cubot_KingKong%208/FRP_BACKUP_(2026-5-28_17-36-19)/
Format FRP... [P1] OK
Writting FRP data... OK
Formatting "userdata" partition... [P1] OK
Formatting "metadata" partition... [P1] OK
Formatting "md_udc" partition... [P1] OK
Wipe data done!

Mensaje modificado por tona12 el May 28 2026, 05:43 PM