Aporte Frp Hotwav Hyper 7 Opciones

[abreum7491]

1- selecionar madiatek

2- conectar presionando volumen + y -

Selected model: Mediatek Mediatek
Operation: Erase FRP
Software version: 9.6

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to [BOX] in BROM/PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM39 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Waiting for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0959
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Get sec config... OK [000000E0]
Active sec flags: []
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port,usb2ser.sys,3.0.1504.0]
Device found at COM39 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0959
Get sec config... OK [000000E0]
Active sec flags: []
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6877]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0xE3AA666F, 0x70961BE5, 0xCB41B659, 0x92A1ED4F
Get Chip ID... [MT6877]
Get SOC ID... [08A51F45A4B61D4940BDC06DF569563C8B48D7719A021818597EAA24771C4185]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [17]
Send preloader... OK
Start preloader... OK
Checking preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): MT256GAXAT4U31 (0104)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : MT256GAXAT4U31
UFS_FWVER : 0104
BLOCK_SIZE: 0x0000001000 (4,00Kb)
UFS_LU0 : 0x0000400000 (4,00Mb)
UFS_LU1 : 0x0000400000 (4,00Mb)
UFS_LU2 : 0x3B96000000 (238,34Gb)
RAM INFO:
INT_SRAM: 0x0000070000 (448,00Kb)
EXT_RAM : 0x0200000000 (8,00Gb)
HEALTH:
Pre EOL Info: normal
DeviceLifeTimeEstA: 0% - 10% device life time used
DeviceLifeTimeEstB: 0% - 10% device life time used
Checking USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Checking A/B state... OK [A]
Read product info... [EXT4] ... OK
Product Brand : HOTWAV
Product Manufacturer : HOTWAV
Product Model : Hyper 7
Product Name : Hyper_7
Product Device : Hyper_7
Product Board : k6877v1_64_k419
Board Platform : mt6877
Build ID : HOTWAV_Hyper_7_V01_20250225
Build Date : Tue Feb 25 20:18:40 CST 2025
Display ID : HOTWAV_Hyper_7_V01_20250225
Security Patch : 2025-02-05
Version SDK : 34
Version Release : 14
Version Codename : REL
Firmware Version : p1rck61v164bspP3
Userdata FS Type : F2FS
Read partition "frp"... OK
Backup saved to C:/Program%20Files%20(x86)/Z3X/Pandora/Backup/MTK/Mediatek_MT6877/FRP_BACKUP_(2025-9-29_13-0-14)/
Format FRP... [P1] OK
Writting FRP data... OK
Erase FRP done!