Reparar Ixxi Infinix Hot 20s X6827 Not Brom Opciones

[nandungortheb]

Repair ixxi infinix HOT 20S X6827
Security Patch: 2023-06-05 NOT Brom

habilitar BROM con umt mtkv0.7a
- ir a infinix 2023 y seleccionar enable BROM(PL) y darle en execute.

con pandora reparar F4
- seleccionamos infinix mediatek y darle en reparar.
no repare con umt por que a veces me toca formatear NV para que me deje reparar, entonces decidi mejor con pandora.
me di cuenta que pandora saco un update para infinix y tecno para bootear con preloader type 1 y 2, pero ya habia activado brom con umt
no lo pude testear.

Operation : Enable BROM (PL)
Waiting for Device...Found
Port : MediaTek PreLoader USB VCOM (Android) (COM74)
Device Path : \\?\usb#vid_0e8d&pid_2000#5&771f8df&0&9#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Driver : MediaTek Inc., 3.2.0.0 [usb2ser.sys]
Mode : PRELOADER
Hw ID : MT6781 [1066] Helio G96
Details : 8A00,CA00,0000
Sec. Config : [SBA:True] [SLA:False] [DAA:True]
MEID : C6818A4F9769CCD3AE8D68B973BD06A1
SoC ID[0] : 857AFC8543AF22860E62F9DF4FEA0F7C
SoC ID[1] : F4EE44DEC673E87E1EEE333A7B33BE5B
WARNING! DA Auth is Enabled! Only Special DA will work!
Sending 1st DA..OK
Jump DA Address...OK
Syncing...OK
Checksum Level is Storage
Connection : preloader
Speed : HIGH-SPEED
Reading RAM Configuration...OK
Sending 2nd DA...OK
Int. RAM : 0x0000000000060000 [384.00 KB]
Ext. RAM : 0x0000000200000000 [8.00 GB]
Flash ID : KM8L9001JM-B62
CID : CE014B4D384C393030314A4D2D423632
BOOT1 : 0x0000000000400000 [4.00 MB]
BOOT2 : 0x0000000000400000 [4.00 MB]
RPMB : 0x0000000000400000 [4.00 MB]
USERAREA : 0x0000001DCB000000 [119.17 GB]
Connected to High-Speed DA Port
Reading Partition Table...OK
Reading Preloader Backup...Done
Preloader : RAW_PLDR_20230911_145832.bin
Erasing preloader...Done
Now you can do opertaion in BROM mode.
To return to normal, use [Disable BROM] and select preloader backup.
[UltimateMTK2 v0.7a]

Selected model: Infinix Mediatek
Operation: Repair
Software version: 5.8
Work ID: 7875865

Connect phone in PRELOADER Mode
Waiting for device... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek PreLoader USB VCOM (Android),usb2ser.sys,3.0.1504.0]
Device found at COM74 [PRELOADER]
Open port... OK
Send start cmd... OK
Get HW code from device... 1066
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6781]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Preloader exist. Skip connection verification.
Get ME ID... OK
ME_ID = 0x4F8A81C6, 0xD3CC6997, 0xB9688DAE, 0xA106BD73
Load DownloadAgent... OK
Search DA... OK [3]
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [PRELOADER]
Preloader alive. Skip initializing external RAM
Get device info... OK
UFS CID (FW VER): KM8L9001JM-B624 (0700)
Send preloader... OK
Load DownloadAgent... OK
Search DA... OK [11]
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8L9001JM-B624
UFS_FWVER : 0700
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000060000 (384.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
Checking USB status... USB_HIGH_SPEED
[EFUSE INFO]: BROM not disabled
Read partitions info from phone... OK
Checking A/B state... OK [B]
Read product info... [EROFS] ... OK
Product Brand : Infinix
Product Manufacturer : INFINIX
Product Model : Infinix X6827
Product Name : TSSI
Product Device : FULL-64
Product Board : Infinix-X6827
Board Platform : connac1x
Build ID : SP1A.210812.016
Build Date : Tue Jun 13 23:36:03 CST 2023
Display ID : INFINIX-S-64-230613V515
Security Patch : 2023-06-05
Version SDK : 31
Version Release : 12
Version Codename : REL
Firmware Version : 230613V1226
Userdata FS Type : F2FS
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Read IMEI... OK
IMEI 1: 35750856XXXXXXX
IMEI 2: 35750856XXXXXXX
Repairing IMEI...
IMEI 1: 35750856XXXXXXX
IMEI 2: 35750856XXXXXXX
Write IMEI [NVDATA]... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!

Mensaje modificado por nandungortheb el Sep 11 2023, 03:42 PM