Xiaomi Mi6 Account Y Frp Remove Con Umt - Qcfire Miui 11 Opciones

[onay95]

hagan testpoint y lo conectan en 9008 mode, abren umt qcfire y en la pestaña xiaomi special tocan reset mi account, luego si tiene frp van a la pestaña read & tools, seleccionan el modelo xiaomi mi6 y tocan reset frp
ya cuando encienda activan depuracion usb y le dan en xiaomi special y tocan anti relock, y listo, le hacen hard reset y listo
aqui los log

Reset Mi Account

Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1E00500 [8998] 00000000
OPK_DATA : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8998_002]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, UFS, 128 GB
LU Count : 6 [0x01C25000] [0x00000800] [0x00000800] [0x00008000] [0x00194000] [0x00008000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi MI 6 [sagit]
Software : PKQ1.190118.001, V11.0.6.0.PCAMIXM [Sat Mar 7 23:01:50 CST 2020]
Android Ver. : 9
Patch Level : 2019-09-01
Resetting Mi Account Data...Done
Preparing Data...Done
Formatting Userdata...Done
When phone is completely ON, connect to Internet and add Mi Account.
-------------- INFORMATION --------------
New Firmware may cause hang on logo.
In such case, you need to flash phone to recover.
Or downgrade firmware and try Reset Mi Account again.
Operation Finished.
QcFire Ver. 5.5

FRP Remove

Device : Xiaomi Mi 6
Operation : Reset FRP
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM30)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.2.0
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1E00500 [8998] 00000000
OPK_DATA : F7337FE47B192EF4D1BA34CB4E879F0C6B771D06D2DE87BF21F65BA3303834E1
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8998_002]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : MSM8996, UFS, 128 GB
LU Count : 6 [0x01C25000] [0x00000800] [0x00000800] [0x00008000] [0x00194000] [0x00008000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 131072, Sector Size: 4096
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi MI 6 [sagit]
Software : PKQ1.190118.001, V11.0.6.0.PCAMIXM [Sat Mar 7 23:01:50 CST 2020]
Android Ver. : 9
Patch Level : 2019-09-01
Resetting FRP Lock.......Done
Operation Finished.
QcFire Ver. 5.5

y por ultimo antirelock

Operation : Mi Anti Relock
Checking for device in ADB mode...Found!
Searching for Device in ADB Mode...Found
Brand : Xiaomi
Model : MI 6
Product : sagit
Device : sagit
Andriod Ver. : 9
Patch Level : 2019-09-01
Bootloader : unknown
Build ID : PKQ1.190118.001
Build Date : Sat Mar 7 23:01:50 CST 2020
Disabling Mi Account Relock...Verified OK... Done
Operation Finished.
QcFire Ver. 5.5