Aporte Format Spd Eyo S270-lol Sc6531 Opciones

[movilGSM]

Hola amigos del clan. Aqui les dejo la forma correcta de quitar codigo de usuario a un EYO e270LOL con volcano. Primero seleccionan el boot que es sc6531, (SPD) Le dan "Read Flash" (muy importante) y esperan que termine despues le dan "format" Es posible que despues no le encienda el cel, no asustarse. Lo vuelven a flashear con el back up que hizo la caja, le vuelven a dar format y van a la ocion "EagleEye" COn el cel conectado le dan a "Collect" y presionan el power (hasta 3min) hasta que el cel arranque y listo. espero les sirva. Aqui estan los logs:


2015-05-29 16:26:55 >>Volcano Updated: 2015-04-03
2015-05-29 16:26:55 >>Connecting...
2015-05-29 16:26:59 >>Connection successful,connected state!
2015-05-29 16:26:59 >>Version: V3.8
2015-05-29 16:26:59 >>SN:422-065-520
2015-05-29 16:26:59 >>Port:COM9
2015-05-29 16:26:59 >>After format or Flash you have to press & hold power button for at least 1.30 mins.
2015-05-29 16:26:59 >>Note for win7 users :
2015-05-29 16:26:59 >>Start your Win 7 64bit with F8 key and choose 'Disable Driver Signature Enforcement'.
2015-05-29 16:26:59 >>After that the spd drivers will have the ability to be loaded.
2015-05-29 16:27:44 >>Available Ports:COM1 COM9
2015-05-29 16:27:44 >>Detection initiated...
2015-05-29 16:27:45 >>Vcc: null
2015-05-29 16:27:45 >>Gnd: 5
2015-05-29 16:27:45 >>Analyzing D+ and D-...
2015-05-29 16:27:46 >>D+ = 3, D- = 2
2015-05-29 16:27:46 >>Detection D+/D- with 0,97 seconds.
2015-05-29 16:27:46 >>Continue to detect BOOT pin...
2015-05-29 16:27:51 >>Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
2015-05-29 16:27:51 >>BOOT(Pull Down) = 4
2015-05-29 16:27:51 >>Setting...
2015-05-29 16:27:55 >>Find USB device:SPRD U2S Diag (COM15), (VID_1782&PID_4D00)
2015-05-29 16:27:55 >>Pinouts setting complete!
2015-05-29 16:27:55 >>
2015-05-29 16:27:55 >>
2015-05-29 16:27:56 >>Internal version: SPRD3
2015-05-29 16:27:56 >>Boot downloading...
2015-05-29 16:27:57 >>Start boot please wait a moment....
2015-05-29 16:28:01 >>Spreadtrum Boot Block version 1.2
2015-05-29 16:28:01 >>CPU TYPE:SC6531 [65310001]
2015-05-29 16:28:01 >>FLASH ID: 00C8006000160000
2015-05-29 16:28:01 >>Flash Type: SF_GD25LQ32
2015-05-29 16:28:01 >>Size:0x400000(4MB)
2015-05-29 16:28:04 >>Writing...(0)
2015-05-29 16:29:11 >>Flash file C:\VolcanoBox\EYO_20150528_182726_FullFlash.bin has been written.
2015-05-29 16:29:17 >>Detection initiated...
2015-05-29 16:29:17 >>Vcc: null
2015-05-29 16:29:17 >>Gnd: 5
2015-05-29 16:29:17 >>Analyzing D+ and D-...
2015-05-29 16:29:18 >>D+ = 3, D- = 2
2015-05-29 16:29:18 >>Detection D+/D- with 0,98 seconds.
2015-05-29 16:29:18 >>Continue to detect BOOT pin...
2015-05-29 16:29:23 >>Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
2015-05-29 16:29:23 >>BOOT(Pull Down) = 4
2015-05-29 16:29:23 >>Setting...
2015-05-29 16:29:27 >>Find USB device:SPRD U2S Diag (COM15), (VID_1782&PID_4D00)
2015-05-29 16:29:27 >>Pinouts setting complete!
2015-05-29 16:29:27 >>
2015-05-29 16:29:27 >>Internal version: SPRD3
2015-05-29 16:29:27 >>Boot downloading...
2015-05-29 16:29:29 >>Start boot please wait a moment....
2015-05-29 16:29:32 >>Spreadtrum Boot Block version 1.2
2015-05-29 16:29:32 >>CPU TYPE:SC6531 [65310001]
2015-05-29 16:29:32 >>FLASH ID: 00C8006000160000
2015-05-29 16:29:32 >>Flash Type: SF_GD25LQ32
2015-05-29 16:29:32 >>Size:0x400000(4MB)
2015-05-29 16:29:35 >>The phone is setting back to Factory...
2015-05-29 18:46:46 >>Volcano Updated: 2015-04-03
2015-05-29 18:46:46 >>Connecting...
2015-05-29 18:46:49 >>Connection successful,connected state!
2015-05-29 18:46:49 >>Version: V3.8
2015-05-29 18:46:49 >>SN:422-065-520
2015-05-29 18:46:49 >>Port:COM9
2015-05-29 18:46:49 >>After format or Flash you have to press & hold power button for at least 1.30 mins.