Nokia 5130 Muerto - Clan GSM - Unión de los Expertos en Telefonía Celular

ClanGSM.com

►Reglamento ►Política de Privacidad Ayuda BUSCADOR Miembros Calendario

Más Opciones de Búsqueda

Bienvenido, invitado ( Identificarse | Registrarse )

Clan GSM - Unión de los Expertos en Telefonía Celular > Cajas y Dongles GSM > Cementerio de Cajas (Sin Actualizaciones ni Soporte) > CYCLONE Box

Reply to this topic

Start new topic

Nokia 5130 Muerto, ayuda

ivan23 Ver Perfil del Miembro	Dec 20 2011, 06:38 PM Publicado: #1
Colaborador del Clan Grupo: Miembros Mensajes: 652 Agradecimientos: 764 Registrado: 14-April 11 Desde: mexico df Miembro No.: 201,375	comento amigos del clan que llego a mi local un nokia 5130 funcionando solo tenia problemas de reproductor decidi meterle el software (flashear) y en los ultimos pasos marco error desde entoces esta muerto trate de levantarlo con phoenix pero no podido hacer que me lo reconosca para enpesar el flasheo con cyclone por usb no me detecta los drivers y por cable mochila sale esto. Booting CMT... CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000 CMT_EM_ASIC_ID: 00000296 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 225001102FBD7D56BB7A6A2A0D76B7816A06E74E CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723 CMT_BOOT_ROM_CRC: 273F6D55 CMT_SECURE_ROM_CRC: DFAAF68F CMT Ready! Searching for BootCode: DualLine 32Bit RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using OLD BB5 FLASHING PROTOCOL If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR FlashContent[0,CMT]: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF, NOR FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit Searching for BootCode: DualLine 32Bit FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled Warning: PAPUBKEYS Hash Missing! APE Boot skipped on user request Flashbus Write baud set to 5.0Mbits Restarting MCU... Processing pre flash tasks... Backing up RPL... RPL Creation started... Processing CMT Part... Sending User Abort Signal... CBUS Request Error -> User abort Sending User Abort Signal... CBUS Request Error -> User abort Failed to enable VBAT -> No answer from CBUS Warning: Phone not detected, using Rap Public ID in FileName and reading Certificates Only Booting CMT... CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000 CMT_EM_ASIC_ID: 00000296 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 225001102FBD7D56BB7A6A2A0D76B7816A06E74E CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723 CMT_BOOT_ROM_CRC: 273F6D55 CMT_SECURE_ROM_CRC: DFAAF68F CMT Ready! Searching for BootCode: DualLine 32Bit RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using OLD BB5 FLASHING PROTOCOL If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR FlashContent[0,CMT]: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF, NOR FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit Searching for BootCode: DualLine 32Bit FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled Warning: PAPUBKEYS Hash Missing! APE Subsystem Not Found Flashbus Write baud set to 5.0Mbits Failed to Create RPL from phone -> No target file chosen RPL backup thread finished, continuing... Backing up simlock... Simlock backup problem -> Phone not detected Backup simlock thread finished, continuing... Pre flash tasks finished, continuing... Processing rm495__07.97.ppm_mena_a1 (CMT)... Booting CMT... CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000 CMT_EM_ASIC_ID: 00000296 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 225001102FBD7D56BB7A6A2A0D76B7816A06E74E CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723 CMT_BOOT_ROM_CRC: 273F6D55 CMT_SECURE_ROM_CRC: DFAAF68F CMT Ready! rm495__07.97.ppm_mena_a1, Type: Flash Image, Algo: BB5, BB5 ALGORITHM Searching for BootCode: DualLine 32Bit RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using OLD BB5 FLASHING PROTOCOL If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR FlashContent[0,CMT]: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF, NOR FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit Searching for BootCode: DualLine 32Bit FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled Warning: PAPUBKEYS Hash Missing! Flashbus Write baud set to 5.0Mbits Started group flash erase EraseArea[0,CMT]: 0x01520000-0x01DBFFFF, NOR Waiting 320s for erasure finish... Erase taken 0.780s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Block Write Failed -> Programming status failed, some error occured while writing flash data Processing Flash Image Failed -> Failed to write all blocks Failed to Process all Image files -> Failed to process rm495__07.97.ppm_mena_a1 si alguien me ayudaria a levantarlo via cyclone de antemano gracias. -------------------- si Dios contigo quien contra ti. gracias por colaborar en el clan gsm. el clan lo hacemos todos aporta y da gracias. cyclone,z3x full,setool full ( lgtool),sigmabox pack1 y 2,xtc 2 clip, nck box.

Anunciante Autorizado	Dec 20 2011, 06:38 PM Publicado: #
Auspiciador de ClanGSM Estas ofertas pudieran interesarte.

RanKeao Ver Perfil del Miembro	Dec 20 2011, 10:17 PM Publicado: #2
Miembro del Clan Grupo: Miembros Mensajes: 70 Agradecimientos: 25 Registrado: 23-January 11 Desde: santiago Miembro No.: 174,304	Amigo prueba cargar la bateria con un cargador externo y tirale la flash via usb, desmarca las casillas de bkp simlock para que sea mas rapido el proseso. En coneccion selecciona usb, luego ve a flash selecciona tu firmware (verifica si es la vercion mas alta la que dispones) luego quita las casillas bkp rpl y bkp simlock y flashea con normalidad.

A continuacion 1 usuario(s) le Agradece(n) a RanKeao por su Colaboracion: ivan23

« Posterior · CYCLONE Box · Anterior »

Reply to this topic

Start new topic

1 usuario(s) está(n) leyendo este tema (1 invitado(s) y 0 usuario(s) anónimo(s))

0 usuarios(s) registrado(s):

Modo de Ver: Estándar · Cambiar a: Lineal+ · Cambiar a: Outline

Suscribirse · Enviar por E-Mail · Imprimir · Suscribirse a este Foro

Web Analytics

Ver Visitas

Fecha y Hora actual: 19th April 2026 - 10:57 AM

►Reglamento ►Política de Privacidad

Todos los derechos reservados ClanGSM.com © 2007-2026

Este sitio web usa cookies, puedes ver la política de cookies, aquí -

Política de cookies +