Actualizaciones De La Riff Box Solo Aqui Opciones

[Eliminado_TecnoServicio_*]

RIFF JTAG - Samsung GT-B7330 Omnia PRO Boot Repair Supported

22/03/2011 Samsung GT-B7330 Omnia PRO Reparación de arranque compatibles

Por favor, comience JTAG Manager y haga clic en "Buscar actualizaciones" botón. Se le notificará acerca de las nuevas DLL, descargarlo y reinicie el software.
"Samsung_B7330.dll" contiene la disposición de las patillas, las instrucciones y archivos necesarios para la reparación de Samsung GT-B7330 Unbrick OmniaPRO - Reparación de inicio.

TecnoServicio

Mensaje modificado por TecnoServicio el Mar 22 2011, 03:52 PM

[Anunciante Autorizado]

[TELCEL]

RIFF JTAG Updates - HTC Ozone/Chief, JTAG Manager v1.29 and more


31.03.2011 HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported




Resurrecting HTC Chief is easy:
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000′.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.


To resurrect HTC Chief:
Solder JTAG cable to HTC Chief JTAG pads;
Make sure HTC Chief is selected in the list of models;
Insert battery and connect USB Cable;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


31.03.2011 JTAG Manager v1.29, RIFF Box Firmware v1.21 released

JTAG Manager 1.29
—————————
Fixed bug with plugins managing in case there is more than 1 plugin DLL available;
Currently selected plugin is remembered now and will stay on next startups;
Fixed Access Violation error during software startup in case there is none resurrector DLL present;
Added Reset Method selection feature for more precise reset operation when Custom Target Settings is active;
Updates manager & Updates tracking were completely reworked, and now are based not on the system time but on file’s hashing.
Thus since now on the JTAG Manager’s installation folder can be copied/moved/re-installed (whatever else) without need to re-download full set of files again.
(SDK): more functions are now available (exported) for future Resurrector DLLs;
Many cosmetic changes;
FINALLY: “healed” the optimized DLL loading scheme:
User shall see: “Found and Initialized: XXX New and YYY Old External Repair Pack(s)” where XXX must be always non-zero only on first startup after there were new DLLs downloaded from the support.
On following JTAG Manager startups XXX shall be always equal to zero (!!!)
For example, after downloading 3 more new DLLs while there were 100 Resurrector DLLs already installed, after JTAG Manager restarts user shall see:
Found and Initialized: 3 New and 100 Old External Repair Pack(s)
on next and all following restarts user shall see:
Found and Initialized: 0 New and 103 Old External Repair Pack(s)
Re-worked balloon hints system – Own (not windows’) balloons are shown, so no matter now what are the windows’ tray icon settings are.
Added balloon hints for cases when target is not detected, error code 0×45, Device Id = 0x000000E1.
Don’t forget that balloons hints can be switched on or off from the DCC Read/Write page – click “Notifications…” and select”For Advanced Users” page to see settings
- JTAG Manager now has new Icons http://www.jtagbox.com/wp-includes/i...icon_smile.gif
- Improved JTAG Manager restarting during updating itself
Firmware 1.21
—————————
Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.
RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;

31.03.2011 RIFF Data Exchange Plugin 1.00 released


First release of the RIFF Data Exchange Plugin: please download it, and then select it on Usefull Plugins page in the JTAG Manager to read short description about the plugin’s abilities. In short it allows RIFF BOX users to share and use Full Image files in centralized manner without need to waste a lot of time for browsing countless forums.


Because of big sizes of Full Image files, we don’t host them, instead users share links to file sharing servers where the files are actually uploaded. (like megaupload.com, rapidshare.com and others) You can browse existent links for required image file or share your image file (by sharing a http link) to help other RIFF BOX users.


If you share image file please take attention to carefully fill file details so for other people this to be an easy task to search for required file (link)
If you used link to download file and found it good or bad or link to be broken – please Rate this link so other users see the usability of the link.
At the moment of first release of this plugin there are already few links shared so you’ll catch the idea fast.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


www.jtagbox.com

http://www.jtagbox.com/

Mensaje modificado por TELCEL el Mar 31 2011, 11:11 AM

[TELCEL]

RIFF JTAG - HTC Advantage X7510 (HTC Athena) Unbrick - Boot Repair supported


04.04.2011 HTC Advantage X7510 (HTC Athena) Unbrick – Boot Repair supported



Resurrection of HTC Athena is easy. Most convenient is to have USB cable connected and battery inserted.
If during connection progress bar in JTAG Manager keeps running from 0 to 100% press with stylus the reset button on the phone (reset button is near to the JTAG pads).
Resurrector will reflash IPL and SPL areas. You can select SPL version to be flashed in the settings window which popups before resurrection. IPL which is flashed: “ATHENA IPL DVT 2.02 H3” version.
Current resurrector works only with HTC Athena hardware revisions which have DiskOnChip H3 memory chip installed. If you have hardware revision with DiskOnChip G4 memory chip used then select different resurrector.
To resurrect HTC Athena with DiskOnChip H3:
Solder JTAG cable to HTC Athena JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure HTC Athena is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Camera’ key and press ‘Power ON’ key or use stylus to press ‘Reset’ button. In few seconds you should see TriColor picture.
Additional info:
DiskOnChip H3′s full NAND memory chip is divided into partitions by the internal memory controller. Thus DCC Loader creates virtual FLASH chip for each partition – you can read/write these partitions by selecting proper ROM index (“Access ROMi Address Space”) on the JTAG Manager’s DCC Read/Write page;
DiskOnChip H3 has no spare zones, thus only Main field must be used during write operations. ECC Enable checkbox has no meaning here.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


http://www.jtagbox.com/jtag-news/rif...air-supported/

[TELCEL]

RIFF JTAG - CDMA Day ! QSC1100, Micromax C111, Huawei C2830 supported


06.04.2011 CDMA QUALCOMM QSC1100 Generic DLL released



Resurrector QSC1100 X14 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU’s internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.


Initial H/W init sequence will setup MCU’s PLL with these parameters:
Clock Multiplier = 0×14
Since few different versions of QSC1100 resurrector may exist (with different multiplier values) you may select the one which suits best to your device

http://www.jtagbox.com/jtag-news/riff-jtag...pair-supported/


Resurrecting Micromax C111 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
There are 2 different hardware revisions of this phone – one is based on Qualcomm QSC1100 MCU and other – is Qualcomm QSC6010 MCU. Current resurrector shall be selected if you have QSC1100 revision.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x6FFFFF).
To resurrect Micromax C111:
Solder JTAG cable to Micromax C111 JTAG pads;

Connect ignition cable for auto power on or use battery;
Make sure Micromax C111 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

06.04.2011 CDMA Huawei C2830 Boot repair supported
http://www.jtagbox.com/jtag-news/riff-jtag...pair-supported/


Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.


To resurrect Huawei C2830:
Solder JTAG cable to Huawei C2830 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C2830 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[TELCEL]

RIFF JTAG - Samsung S7230E Wave 723 Unbrick – Boot Repair supported


08.04.2011 Samsung S7230E Wave 723 Unbrick – Boot Repair supported





Resurrecting Samsung S7230E is easy. To power the phone connect USB cable and insert battery. In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.


To resurrect Samsung S7230E:
Solder JTAG cable to Samsung S7230E JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung S7230E is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.


To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

Mensaje modificado por TELCEL el Apr 8 2011, 12:02 PM

[dapx]

RIFF JTAG - HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair sup

09.04.2011 HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair supported


Resurrecting HTC Mozart is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.60.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD6710000′.


To resurrect HTC Mozart:

* Solder JTAG cable to HTC Mozart JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure HTC Mozart is selected in the list of models;
* If you use battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[dapx]

RIFF JTAG - CDMA HTC Droid Eris, HTC Polaris and more
12.04.2011 CDMA HTC Droid Eris, Unbrick, Boot Repair, ModelID repair supported


Resurrecting HTC Droid Eris is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB0010000′.
To resurrect HTC Droid Eris:

* Solder JTAG cable to HTC Droid Eris JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure HTC Droid Eris is selected in the list of models;
* If you use battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
* Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;

12.04.2011 HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported


Resurrecting HTC Polaris is easy.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000′.


To resurrect HTC Polaris:

*
* Solder JTAG cable to HTC Polaris JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure HTC Polaris selected in the list of models;
* If you use battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

12.04.2011 QUALCOMM NOR Generic DLL-s update:

* QSC1100_X14_NOR,
* QSC60XX_L18_D08_NOR,
* QSC60XX_L20_D08_NOR,
* QSC60XX_L24_D08_NOR

Whats new:

* Added support for NOR Chips which have Intel/Sharp Extended Command Set (according to the CFI specification)

This means any NOR flash chip which is manufactured by CFI standard (it means all NOR flash chips) will be supported with above listed DLL-s. There is no need to update DCC Loaders for single flash chip ID, since configuration data are obtained from CFI.

12.04.2011 RIFF JTAG Manager v1.30, RIFF Box Firmware v1.22 released

Firmware 1.22
---------------------------

* Fixed bugs in ARM7 core handling routines



JTAG Manager 1.30
---------------------------

* Added DISABLE_POLLING request processing from DCC Loader

(used by DCC Loaders which have small RAM size available and there is no DCC RX polling is implemented in RIFFBOX firmware for current core);

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[TELCEL]

RIFF JTAG - CDMA Samsung SCH-S109 (MSM6000) Repair supported and more !



20.04.2011 CDMA Samsung SCH-S109 (MSM6000) Repair supported


Resurrecting Samsung S109 is simple. Phone is auto powered on with charger connected; battery presence is not required.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x3FFFFF).


To resurrect Samsung S109:
Solder JTAG cable to Samsung S109 JTAG pads;
Connect ignition cable for auto power on or use battery;
Make sure Samsung S109 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

20.04.2011 JTAG Manager v1.31, RIFF Box Firmware v1.23 released


Whats new :


JTAG Manager 1.31
“RUN/STOP” Loaders functionality is added (and alternative to the DCC Loaders)
This is required for some ARM7 cores when Debug Communication Channel (DCC) to/from core is not functional (like in MSM6000)


Firmware 1.23
Added 8/16/32-bit bus read/write access rotuines for ARM7 core
ARM7 debug is now available in ARM/Thumb modes (use the GDBServer for this);

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

Mensaje modificado por TELCEL el Apr 20 2011, 10:58 AM

[TELCEL]

RIFF JTAG - CDMA Motorola W150i (MSM6000) Repair supported






21.04.2011 CDMA Motorola W150i (MSM6000) Repair supported


Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.


To resurrect Motorola W150i:
Solder JTAG cable to Motorola W150i JTAG pads;
Connect charger for auto power on or use battery;
Make sure Motorola W150i is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


http://www.jtagbox.com/

[TELCEL]

RIFF JTAG - CDMA Samsung S239 (MPower) Repair supported

26.04.2011 CDMA Samsung S239 (MPower) Repair supported





Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.


To resurrect Samsung S239:
Solder JTAG cable to Samsung S239 JTAG pads;
Connect ignition cable for auto power on or use battery;
Make sure Samsung S239 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[TELCEL]

RIFF JTAG - Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported


03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported


Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
To resurrect Samsung B2710 do this:
Solder JTAG cable to the Samsung B2710 JTAG pads;
Connect USB cable to phone and PC;
Make sure Samsung B2710 is selected in the list of models
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

http://www.jtagbox.com/

--------------------------------------

Mensaje modificado por TELCEL el May 3 2011, 11:08 AM

[TELCEL]

RIFF JTAG - Samsung Nexus S, HTC Incredible C Unbrick/Boot repair supported


04.05.2011 HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported




Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.


To resurrect HTC Incredible C:
Solder JTAG cable to HTC Incredible C JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Incredible C is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;



04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported


Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.


To resurrect Samsung I9023:
Solder JTAG cable to Samsung I9023 JTAG pads;
Connect microUSB cable to phone and PC;
Insert battery;
Make sure Samsung I9023 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


http://www.jtagbox.com/

Mensaje modificado por TELCEL el May 4 2011, 09:24 AM

[dapx]

07.05.2011 LG CU720 Shine Unbrick – Boot repair supported


Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect LG CU720:

Solder JTAG cable to LG CU720 JTAG pads;
Insert USB Data cable into board and PC;
Make sure LG CU720 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.



Saludos. Enjoy

[dapx]

RIFF JTAG - CDMA Day Again !
09.05.2011 RIFF JTAG – CDMA Day Again ! More power for Indian users !

Whats new:
Added Huawei CDMA models support :

Huawei C2823 Repair, Read/Write NOR flash
Huawei C2809 Repair, Read/Write NOR flash
Huawei C2808 Repair, Read/Write NOR flash
Huawei C2807 Repair, Read/Write NOR flash
Huawei C2607 Repair, Read/Write NOR flash
Huawei C2905 Repair, Read/Write NOR flash

Added ZTE CDMA Model :

ZTE C335 Repair, Read/Write NOR flash

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[SpLock]

RIFF JTAG - Samsung S5830, A867 Unbrick/Repair, Huawei Modem E5830 supported


12.05.2011 Samsung Galaxy Ace S5830 Unbrick – Boot repair supported


Samsung S5830 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


To resurrect Samsung S5830 do this:

Solder JTAG cable to Samsung S5830 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung S5830 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;

12.05.2011 Huawei E5830 Broadband modem Unbrick – Boot repair supported


Resurrecting Huawei E5830 is simple. Just make sure you solder all JTAG signals. Connection can be established with USB Cable connected, though in some rare cases battery presence may be required.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
Please note, if only an USB cable is connected the device is detected by PC as unknown device. So, after resurrection in order to check if modem is alive make sure battery is connected.


To resurrect Huawei E5830:

Solder JTAG cable to Huawei E5830 JTAG pads;
Insert Huawei E5830 modem into any USB port for power;
Make sure Huawei E5830 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;

12.05.2011 Samsung Eternity A867 Unbrick - Boot repair supported


The Samsung A867 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.


To resurrect Samsung A867:

Solder JTAG cable to Samsung A867 JTAG pads;
Connect USB cable;
Make sure Samsung A867 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[dapx]

RIFF JTAG - CDMA Huawei C5589, Dopod Magic A6188 ,Samsung Z630, Huawei E5832 added
13.05.2011 CDMA Huawei C5589 Unbrick – Boot repair supported




Resurrecting Huawei C5589 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0×2230


To resurrect Huawei C5589:

Solder JTAG cable to Huawei C5589 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C5589 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;



Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported


The HTC Magic (SAPP400) is based on ESM7206A chipset. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.53.02000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘SAPP*****’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.


To resurrect HTC Magic (SAPP400):

Solder JTAG cable to HTC Magic (SAPP400) JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Magic (SAPP400) is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Back (←)’ key and press ‘Power ON’ button. In few seconds you should see download mode saying Fastboot USB.

13.05.2011 Samsung Z630 Unbrick – Boot repair supported


Resurrection of Samsung Z630 requires battery or external power supply. Most convenient way is to use additionally an USB cable: in this case power is auto powered on and there will be no need to hold power on key during connection startup.
Please note, phone will be detected even with only USB cable connected, but stable connection and stable data exchange will be achieved only when battery (or external power supply) is connected too.


To resurrect Samsung Z630:

Solder JTAG cable to Samsung Z630 JTAG pads;
Insert battery (or connect external power supply to the battery pads) and connect USB cable;
Make sure Samsung Z630 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ’4′ key and press ‘Power ON’ button. In few seconds you should see light-blue screen.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Enjoy. Saludos.

[dapx]

RIFF JTAG - More CDMA Models, Samsung S5250 Unbrick supported
29.05.2011 More CDMA Models, Samsung S5250 Unbrick supported


New CDMA models added today :

ZTE S160
Unicare UN510BF
Unicare ChivaC2
Huawei C5100

Samsung phones :

Samsung S5250
Samsung S5260 (Bug Fix)

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[Eliminado_FixMobile77_*]

RIFF JTAG - More CDMA Models, new bug fix updates today

10.06.2011 More CDMA Models, new bug fix updates today

Whats new :

CDMA Models JTAG support :

Huawei C2605
Micromax MMX 250C
ZTE WP829
LG RD3640
Bug fix updates :

Samsung S5830
HTC Incredible C
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box-JTAF Revolutionç


FixMobile77

[SpLock]

RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair
WHATS NEW!!!


- HTC Desire HD A9191 (HTC Ace) = Unbrick, IMEI, CID, ModelID, Simlock repair = WORLD FIRST ! ! !

RIFF JTAG - HTC Desire HD Discussion (Repair, Unlock, IMEI Repair)


Firmware 1.25
---------------------------
- added 5.0V USB Power On/Off controlling feature
- changed sequence for 32-bit write accesses for ARM11 core (MSM8xxx support)


JTAG Manager 1.33
---------------------------
- Improved connection policy:
Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages - booting stage and working stage.
Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup
by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
After "booting" stage is complete, the "working" speed is set - the one which is selected by user in the JTAG TCK Speed field.
If Booting Speed in resurrector DLL is hardcoded as 'RTCK' the JTAG Manager would always use RTCK mode during booting stage.
Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically
change booting speed to the fixed TCK too.

- fixed bug: if "Use End Address" and "AutoFull Flash Size" were checked there was error setting valid length to read.

- for Advanced Users: advanced settings are now moved from the DCC Read/Write page ("Notifications...") into separate button on Box Service page (Advanced Settings button)

- added 5.0V USB Power On/Off controlling feature
For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed,
go to "Advanced Settings" page and set desired mode for "Enable 5.0V output" checkbox.
When enabled, 5.0V power will be on after any "JTAG" operation executed and will remain "ON" until
box restart or until "Enable 5.0V output" checkbox is unchecked and any "JTAG" operation is executed.

- added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards)

- if error code 0x3C (write-protect) is received no recover attempts are made.

[dapx]

RIFF JTAG - CDMA Updates again
22.06.2011 CDMA day again, 3 new models supported


Whats new:

Motorola W200 full support
Huawei C2801 full support
Nokia 1006 full support

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Saludos. Enjoy.