ClanGSM.com

Bienvenido, invitado ( Identificarse | Registrarse )

2 Páginas: V   1 2 >  
Reply to this topicStart new topic
Unlock Sp200 17a
Dr Phone´s
mensaje May 8 2019, 02:56 PM
Publicado: #1

Miembro del Clan
*

Grupo: Miembros
Mensajes: 104
Agradecimientos: 242
Registrado: 19-June 18
Miembro No.: 1,053,008
Pais:gt


Compañeros les comparto mi experencia con el unlock al modelo LG SP200 version 17a parche seguridad Marzo 1, 2019.

NOTA: antes que nada cabe aclarar que los resultados fueron de un proceso de mucha lectura sobre otros post y sobre errores de otros colegas. Fue testeado con la Version 17a pero creeria que si seguien los mismos procesos es funcional para versiones anteriores. Doy credito a quien dio inicio con esto en el clan Arturo1971 y a los colegas que comentan sus experiencias en el siguiente Link https://www.clangsm.com/forum/index.php?showtopic=509736 y a los link encontrados.

IMPORTANTE: Al momento de iniciar con la instalacion del firmware y que de ERROR, NO DESCONECTAR BATERIA, solamente retirar cable y seguir insistiendo con la instalacion de Firmware en Octoplus, hasta que termine el proceso. BATERIA con un 90% de carga para evitar problemas.

PASO 1: Realizar lectura de Eproom con Octoplus seleccionando modelo SP200

PASO 2: Cargar firmware SP20013b_to_X210ULMA10d_for_unlock.oct con Octoplus
En este proceso nos dira que no es del modelo exacto, damos que si, todos los archivos seleccionados del firmware los dejamos, nos dira si necesitamos dar Formato UserData, damos que si
en mi caso aca empezo a dar error, SIN REMOVER BATERIA solo cable, volvi a realizar el mismo proceso cuando pedia conectar sin necesidad de precionar vol+ porque ya esta en modo Descarga
solo conectamos y continua el proceso, si vuelve a dar error en algun paso continuar haciendo lo mismo, hasta que nos diga OK todo el proceso.

Fichero Adjunto  SP20017a... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 186.69k ) Número de descargas: 0


Fichero Adjunto  error_sp... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 169.45k ) Número de descargas: 0


Fichero Adjunto  Firmware... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 169.36k ) Número de descargas: 0


En este momento el teléfono ya nos enciende como K8+, en mi caso quedo freezado en el logo no preocuparse, realice un hard reset desde recovery (por si a alguno le funciona con esto) en lo personal continuo el telefono en el logo, no preocupars, continuar con el siguiente paso.

PASO 3: Carga de Firmware desde LG-UP solucionando problema de logo en pantalla
Una vez descargado el Archivo LG-UP descomprimir e instalarlo, para que les funcione sin problema deben sustituir los archivos LGUP.exe y MODEL a la carpeta donde se realizo la instalación en el disco C en mi caso fue a la siguiente direccion... C:\Program Files\LG Electronics\LGUP

Habiendo realizado esto, abren programa LG-UP y conectan el telefono en modo Download (vol+ por 10 seg y conectar usb) seleccionan la opcion CHIPERASE y en archivo BIN seleccionan el que dejo en el archivo SP200.kdz encontrado en la red, proceden a dar Start y al terminar el proceso el telefono enciende Normal.

Fichero Adjunto  Proceso_... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 64.34k ) Número de descargas: 0


PASO 4: Cargar Archivo Eproom leido en paso 1 y LISTO telefono funcionando smile.gif

PD. Esta fue la forma en que yo lo realice, quiza puedan saltarse el paso del primer Firmware unlock.oct y colocar Firmware X210 a la primera, pero seria bajo su riesgo, Comenten Resultados smile.gif

Fichero Adjunto  Unlock_S... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 388bytes ) Número de descargas: 143


Go to the top of the page
 
+Quote Post
A continuacion 7 usuario(s) le Agradece(n) a Dr Phone´s por su Colaboracion:
celular35, cibermovil, dc774, demio, jonitrance, nemesin96, Tecnozaza
Anunciante Autorizado
mensaje May 8 2019, 02:56 PM
Publicado: #

Auspiciador de ClanGSM

Estas ofertas
pudieran interesarte.











Go to the top of the page
 
Quote Post
cghond
mensaje May 10 2019, 11:09 PM
Publicado: #2

Colaborador del Clan
**

Grupo: Miembros
Mensajes: 394
Agradecimientos: 380
Registrado: 28-March 16
Desde: Colonia Victoria
Miembro No.: 812,417
Pais:hn


hola amigo estoy batallando mucho con el lg up sigo los pasos y siempre me salta ese error igual he probado a desinstalar y borrar la carpeta pero el error persiste...

Fichero Adjunto  1.jpg... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 15.58k ) Número de descargas: 0


--------------------
Se que te gustó y aún no me atrevo
Dame una señal para perder el miedo
Go to the top of the page
 
+Quote Post
fercel1
mensaje Jul 25 2019, 02:31 PM
Publicado: #3

Miembro del Clan
*

Grupo: Miembros
Mensajes: 30
Agradecimientos: 61
Registrado: 7-May 09
Miembro No.: 35,938



CITA(cghond @ May 10 2019, 10:09 PM) *
hola amigo estoy batallando mucho con el lg up sigo los pasos y siempre me salta ese error igual he probado a desinstalar y borrar la carpeta pero el error persiste...

Fichero Adjunto  1.jpg... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 15.58k ) Número de descargas: 0


Colega pudiste solucionar tu problema con el LGUP?
Go to the top of the page
 
+Quote Post
arthurlara
mensaje Jul 25 2019, 09:14 PM
Publicado: #4

Miembro del Clan
*

Grupo: Expulsados
Mensajes: 87
Agradecimientos: 109
Registrado: 10-March 16
Desde: mexico
Miembro No.: 806,520
Pais:mx


CITA(fercel1 @ Jul 25 2019, 02:31 PM) *
Colega pudiste solucionar tu problema con el LGUP?

tienen q descargar el lgup que esta publicado en el metodo
que compartio el compa{ero arturo pero tienes que darle alas opciones que vienen dentro de la carpeta para que actibe las otras opciones
y la liberacion es mas facil si solo flashean el sofware sp200.kdz con el programa lgup marcando la opcion chiperase y luego escribir la eppron respalda antes con octopus
Go to the top of the page
 
+Quote Post
lolo24
mensaje Aug 1 2019, 08:06 AM
Publicado: #5

Maestro del Clan
***

Grupo: Miembros
Mensajes: 974
Agradecimientos: 2213
Registrado: 22-January 16
Desde: CUBA
Miembro No.: 791,161
Pais:cu


Hola.

Este modelo siempre lo hago con LG UP, Developer Mode, y opcion Chip Erase,,, En todas las Versiones Funcionando 100%

Saludos


--------------------
Mis Box: SimgaKey PLUS - OctopusBox (Samsung,LG,FrpTool) - UMT + NCK - EFT - GC Pro Key (DEAD) - Infinity Box
- FuriousGold Pack 1,2,3,4,5,6 - Eft PRO - Infinty Box ...ChimeraTOOL


* Use siempre el botón DAR GRACIAS
* Use el buscador antes de Publicar
* Siga las reglas del FORO AQUI
Go to the top of the page
 
+Quote Post
A continuacion 1 usuario(s) le Agradece(n) a lolo24 por su Colaboracion:
Arturo1971
jorgealejandromo...
mensaje Aug 7 2019, 02:49 PM
Publicado: #6

Miembro del Clan
*

Grupo: Miembros
Mensajes: 24
Agradecimientos: 122
Registrado: 2-December 10
Desde: venezuela
Miembro No.: 156,476
Pais:ve


saludos servira tambien para el sp200 18b ? haz hecho alguno con esta seguridad?


CITA(lolo24 @ Aug 1 2019, 09:06 AM) *
Hola.

Este modelo siempre lo hago con LG UP, Developer Mode, y opcion Chip Erase,,, En todas las Versiones Funcionando 100%

Saludos



--------------------
Saludos!!! desde Venezuela.
Atte.
Jorge Mora
Servitec Mora
merida - venezuela
Agradecer No Cuesta ni 1 segundo de tu Tiempo!!!
Go to the top of the page
 
+Quote Post
Rubso
mensaje Aug 14 2019, 07:44 PM
Publicado: #7

Miembro del Clan
*

Grupo: Miembros
Mensajes: 120
Agradecimientos: 565
Registrado: 22-November 15
Desde: Mexico
Miembro No.: 773,325
Pais:mx


CITA(jorgealejandromora @ Aug 7 2019, 12:49 PM) *
saludos servira tambien para el sp200 18b ? haz hecho alguno con esta seguridad?


Acabo de sacar uno con la version SP20018b con el metodo pasado y sin ningun problema de pantalla corrida

1.- Read EEPROM
2.- Write firmware: X210ULMA10d (hard Reset)
3.- Write EEPROM (hard Reset
4.- Listo

Welcome to Octoplus/Octopus Box LG Software version 2.9.3
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LG-SP200
Platform: mt6750
Android version: 7.1.2
SW version: SP20018b_01
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 351980-09-016630-5
MEID: 351980-09-016630
Bluetooth address: B4:F7:A1:2D:67:37
Wi-Fi MAC address: B4:F7:A1:D6:3C:F6
SPC: 894141
--------------------------------------------------------------------------------
Selecting output file...OK
Destination file: "SP200_35198009016630_14-08-2019_17-15-20.EEP"
Reading EEPROM...OK
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG Qualcomm
Selected port: COM34
Selected model: MS428
Reading info...
Model ID: LG-SP200
Incompatible model ID!
IMEI:
Android version:
Battery level: 50%
Mode: Emergency
Initializing flash...OK
Platform: mt6750
SW version: SP20018b_01
Android version: 7.1.2
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
--------------------------------------------------------------------------------
Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones,
modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any
installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your
computer during the flashing!
--------------------------------------------------------------------------------
Opening "SP200.oct"...OK
Selecting firmware partitions...OK
Selected default partitions!
Setting options...OK
Do you want to format User Data?
Reading partitions...OK
Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing preloader...OK
Writing pgpt...OK
Writing lk...OK
Writing lk2...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing logo...OK
Writing lo_bak_go...OK
Writing secro...OK
Writing tee1...OK
Writing tee2...OK
Writing factory...OK
Writing efuse...OK
Writing md1img...OK
Writing md1dsp...OK
Writing md1arm7...OK
Writing md3img...OK
Writing system...OK
Writing lafbak...OK
Writing sgpt...OK
Writing ftm...OK
Writing cache...OK
Writing OP...OK
Writing userdata...OK
Reading partitions...OK
Formating RCT...OK
Formating MPT...OK
Finalizing...OK
Writing firmware done!
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LM-X210ULMA
Platform: mt6750
Android version: 7.1.2
SW version: LMX210ULMAAT-00-V10d-LAO-COM-MAR-16-2018-ARB00+
0
LAF Version: 1.1
Product ID: 00000000000000000000000000000
IMEI:
Target operator: LAO
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 350305-26-000000-1
MEID: 350305-26-000000
Bluetooth address: 00:05:C9:00:00:00
Wi-Fi MAC address: 00:00:00:00:00:00
SPC: 000000
--------------------------------------------------------------------------------
Detecting writing method...
LAF Error: 80000121.
Trying second method...
Trying third method...Failed!
Trying third method...OK
Opening "SP200_35198009016630_14-08-2019_17-15-20.eep"...OK
Writing EEPROM...OK
EEPROM succesfully repaired.
Performed by 2.9.3 Software version.

Welcome to Octoplus/Octopus Box LG Software version 2.9.3
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LG-SP200
Platform: mt6750
Android version: 7.1.2
SW version: SP20018b_01
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 351980-09-016630-5
MEID: 351980-09-016630
Bluetooth address: B4:F7:A1:2D:67:37
Wi-Fi MAC address: B4:F7:A1:D6:3C:F6
SPC: 894141
--------------------------------------------------------------------------------
Selecting output file...OK
Destination file: "SP200_35198009016630_14-08-2019_17-15-20.EEP"
Reading EEPROM...OK
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG Qualcomm
Selected port: COM34
Selected model: MS428
Reading info...
Model ID: LG-SP200
Incompatible model ID!
IMEI:
Android version:
Battery level: 50%
Mode: Emergency
Initializing flash...OK
Platform: mt6750
SW version: SP20018b_01
Android version: 7.1.2
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
--------------------------------------------------------------------------------
Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones,
modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any
installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your
computer during the flashing!
--------------------------------------------------------------------------------
Opening "SP200.oct"...OK
Selecting firmware partitions...OK
Selected default partitions!
Setting options...OK
Do you want to format User Data?
Reading partitions...OK
Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing preloader...OK
Writing pgpt...OK
Writing lk...OK
Writing lk2...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing logo...OK
Writing lo_bak_go...OK
Writing secro...OK
Writing tee1...OK
Writing tee2...OK
Writing factory...OK
Writing efuse...OK
Writing md1img...OK
Writing md1dsp...OK
Writing md1arm7...OK
Writing md3img...OK
Writing system...OK
Writing lafbak...OK
Writing sgpt...OK
Writing ftm...OK
Writing cache...OK
Writing OP...OK
Writing userdata...OK
Reading partitions...OK
Formating RCT...OK
Formating MPT...OK
Finalizing...OK
Writing firmware done!
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LM-X210ULMA
Platform: mt6750
Android version: 7.1.2
SW version: LMX210ULMAAT-00-V10d-LAO-COM-MAR-16-2018-ARB00+
0
LAF Version: 1.1
Product ID: 00000000000000000000000000000
IMEI:
Target operator: LAO
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 350305-26-000000-1
MEID: 350305-26-000000
Bluetooth address: 00:05:C9:00:00:00
Wi-Fi MAC address: 00:00:00:00:00:00
SPC: 000000
--------------------------------------------------------------------------------
Detecting writing method...
LAF Error: 80000121.
Trying second method...
Trying third method...Failed!
Trying third method...OK
Opening "SP200_35198009016630_14-08-2019_17-15-20.eep"...OK
Writing EEPROM...OK
EEPROM succesfully repaired.
Performed by 2.9.3 Software version.
Go to the top of the page
 
+Quote Post
A continuacion 5 usuario(s) le Agradece(n) a Rubso por su Colaboracion:
atb29, celular35, david777, jorgealejandromora, vibcellular
tecnobit2016
mensaje Sep 3 2019, 06:23 PM
Publicado: #8

Miembro del Clan
*

Grupo: Miembros
Mensajes: 3
Agradecimientos: 2
Registrado: 17-December 16
Desde: Cuba
Miembro No.: 906,114
Pais:cu


Alguien que tenga vinculo del sistema sp20018b stock ya q me hace falta reparar el imei a uno porque el sistema de la pc se me daño y perdí la salva de la eeprom y el sistema del x210U no me deja activas el puerto de diagnostico para reparar el imei y poder volver hacer la salva de la eeprom y repetir el proceso de unlock
Ojo esto es para probar no tengo forma de saber si funcionara pero debe poderse hacer, si alguien tiene otra vía de repararle el imei a este modelo después de ponerle el sistema x210U q me ayude por favor. Saludos
Go to the top of the page
 
+Quote Post
VICTORRAV
mensaje Oct 17 2019, 06:14 PM
Publicado: #9

Miembro del Clan
*

Grupo: Miembros
Mensajes: 20
Agradecimientos: 53
Registrado: 23-February 10
Miembro No.: 86,893
Pais:mx


CITA(jorgealejandromora @ Aug 7 2019, 12:49 PM) *
saludos servira tambien para el sp200 18b ? haz hecho alguno con esta seguridad?

100% full con version 19a
Go to the top of the page
 
+Quote Post
A continuacion 1 usuario(s) le Agradece(n) a VICTORRAV por su Colaboracion:
jorgealejandromora
bermudez1980
mensaje Nov 28 2019, 02:12 PM
Publicado: #10

Miembro del Clan
*

Grupo: Miembros
Mensajes: 21
Agradecimientos: 19
Registrado: 18-April 13
Miembro No.: 460,258



Buenas tardes Estimados,
Sera que pueden ayudarme Flashee un LG SP200 version 18B con octopus para liberarlo, hizo todo el proceso, pero me quedo en el logo de K8+, entiendo que flasheandolo con LGUP podria recuperarlo. Pero no he podido instalar el LGUP con todas la opciones solo me presenta Refubish, Update y Fota.

He intentado instalar diversos LGUP pero nada. Aun con los archivos BAT. Hay un ejecutable que es LGPD que al abrirlo me indica que el DLL valido para X210ULMA.

Estoy trabajando con Windows 7 Ultimate.

Alguien que pueda orientarme ya que estoy pegado con este cell.

Saludes

Mensaje modificado por bermudez1980 el Nov 28 2019, 02:15 PM
Go to the top of the page
 
+Quote Post
Dr Phone´s
mensaje Dec 10 2019, 11:20 PM
Publicado: #11

Miembro del Clan
*

Grupo: Miembros
Mensajes: 104
Agradecimientos: 242
Registrado: 19-June 18
Miembro No.: 1,053,008
Pais:gt


CITA(bermudez1980 @ Nov 28 2019, 01:12 PM) *
Buenas tardes Estimados,
Sera que pueden ayudarme Flashee un LG SP200 version 18B con octopus para liberarlo, hizo todo el proceso, pero me quedo en el logo de K8+, entiendo que flasheandolo con LGUP podria recuperarlo. Pero no he podido instalar el LGUP con todas la opciones solo me presenta Refubish, Update y Fota.

He intentado instalar diversos LGUP pero nada. Aun con los archivos BAT. Hay un ejecutable que es LGPD que al abrirlo me indica que el DLL valido para X210ULMA.

Estoy trabajando con Windows 7 Ultimate.

Alguien que pueda orientarme ya que estoy pegado con este cell.

Saludes


Busca en la red el patched para LGUP lo descargas y luego solo cambias los archivos del patched por los que estan en la caperta de instalacion en el Disco C...
Go to the top of the page
 
+Quote Post
Emsel
mensaje Dec 12 2019, 02:08 PM
Publicado: #12

Miembro del Clan
*

Grupo: Miembros
Mensajes: 59
Agradecimientos: 27
Registrado: 11-August 15
Desde: Cuba
Miembro No.: 744,076
Pais:cu


Al que Le de problemas para restaurar backup de eprom por seguridad muy actualizada. Pueden reparar imei con GCPro y listo.

Saludos.
Go to the top of the page
 
+Quote Post
Andosonson
mensaje Dec 26 2019, 08:18 PM
Publicado: #13

Miembro del Clan
*

Grupo: Miembros
Mensajes: 8
Agradecimientos: 3
Registrado: 3-June 13
Miembro No.: 477,653



CITA(VICTORRAV @ Oct 17 2019, 07:14 PM) *
100% full con version 19a

Alguien lo ha probado en el parche Sepember 1,2019 (SP2001Aa)???
Go to the top of the page
 
+Quote Post
master2006
mensaje Dec 27 2019, 03:26 PM
Publicado: #14

Miembro del Clan
*

Grupo: Miembros
Mensajes: 220
Agradecimientos: 1353
Registrado: 16-September 12
Desde: El Salvador
Miembro No.: 384,576



CITA(Andosonson @ Dec 26 2019, 07:18 PM) *
Alguien lo ha probado en el parche Sepember 1,2019 (SP2001Aa)???


Funciona, de hecho de una vez escribió octopus SP20013b_to_X210ULMA10d_for_unlock ----> selecciona el modelo sp200 en octopus LG software version 2.9.3 .

Realiza hard reset ---> vol + power, al encender soltar y presionar power (no soltar vol +)
Si siempre se queda en el logo LG K8+, no te preocupes, sigue al siguiente paso.

Luego con LGUP restaura el firmware X210ULMA10d.kdz ----> chiperase

Restaura el IMEI con la epprom, selecciona el modelo X210ULMA, o escribe el IMEI original del equipo MEID HEX (si no tienes backup ).

Mensaje modificado por master2006 el Dec 27 2019, 03:27 PM
Go to the top of the page
 
+Quote Post
A continuacion 1 usuario(s) le Agradece(n) a master2006 por su Colaboracion:
Andosonson
Andosonson
mensaje Jan 6 2020, 09:53 PM
Publicado: #15

Miembro del Clan
*

Grupo: Miembros
Mensajes: 8
Agradecimientos: 3
Registrado: 3-June 13
Miembro No.: 477,653



CITA(master2006 @ Dec 27 2019, 04:26 PM) *
Funciona, de hecho de una vez escribió octopus SP20013b_to_X210ULMA10d_for_unlock ----> selecciona el modelo sp200 en octopus LG software version 2.9.3 .

Realiza hard reset ---> vol + power, al encender soltar y presionar power (no soltar vol +)
Si siempre se queda en el logo LG K8+, no te preocupes, sigue al siguiente paso.

Luego con LGUP restaura el firmware X210ULMA10d.kdz ----> chiperase

Restaura el IMEI con la epprom, selecciona el modelo X210ULMA, o escribe el IMEI original del equipo MEID HEX (si no tienes backup ).


Tambien funciona en la version SP2001Ba, lo he probado yo

CITA
1/6/2020 08:48:53 PM > Searching for server...
1/6/2020 08:48:54 PM > Trying to ping server...1/6/2020 08:48:54 PM > ok
1/6/2020 08:48:54 PM > Trying connect to server...
1/6/2020 08:48:54 PM > Server greeting: Card updates server v.2.2
1/6/2020 08:48:55 PM > Searching installed cards...
1/6/2020 08:48:55 PM > Found card with s/n: 100097E87
1/6/2020 08:48:55 PM > Server check...
1/6/2020 08:48:56 PM > Server Check succesfull!
1/6/2020 08:48:56 PM > Server Check succesfull!
1/6/2020 08:48:57 PM > Welcome to Octoplus/Octopus Box LG Software version 2.9.7.01
1/6/2020 08:49:13 PM > --------------------------------------------------------------------------------
1/6/2020 08:49:13 PM > Checking data...1/6/2020 08:49:14 PM > OK
1/6/2020 08:49:14 PM > Platform: LG MTK
1/6/2020 08:49:14 PM > Selected port: COM838
1/6/2020 08:49:14 PM > Selected baudrate: 921600
1/6/2020 08:49:14 PM > Selected model: SP200
1/6/2020 08:49:14 PM > Selected USB connection type
1/6/2020 08:49:15 PM > Please, disconnect cable, reconnect battery, connect P999 cable (with 910k resistor)
1/6/2020 08:49:15 PM > or
1/6/2020 08:49:15 PM > Reconnect battery, press and hold "Vol+" for 10 seconds and connect Micro USB cable.
1/6/2020 08:49:25 PM > Phone found at port COM111
1/6/2020 08:49:38 PM > Mode: Emergency
1/6/2020 08:49:38 PM > Initializing flash...1/6/2020 08:49:40 PM > OK
1/6/2020 08:49:41 PM > Model ID: LG-SP200
1/6/2020 08:49:41 PM > Platform: mt6750
1/6/2020 08:49:41 PM > Android version: 7.1.2
1/6/2020 08:49:41 PM > SW version: SP2001Ba_01
1/6/2020 08:49:41 PM > LAF Version: 1.1
1/6/2020 08:49:41 PM > Product ID: VP01S190212001007
1/6/2020 08:49:41 PM > IMEI:
1/6/2020 08:49:41 PM > Target operator: SPR
1/6/2020 08:49:41 PM > Hardware: rev_10
1/6/2020 08:49:41 PM > Battery level: 50%
1/6/2020 08:49:41 PM > Reading partitions...1/6/2020 08:49:41 PM > OK
1/6/2020 08:49:43 PM > Checking security...
1/6/2020 08:49:43 PM > offs: 00380000
1/6/2020 08:49:43 PM > Checking security passed!
1/6/2020 08:49:43 PM > --------------------------------------------------------------------------------
1/6/2020 08:49:43 PM > IMEI: 359634-09-xxxxxxxx-5
1/6/2020 08:49:43 PM > MEID: 359634-09-xxxxxxx
1/6/2020 08:49:43 PM > Bluetooth address: 64:C2:xxxx:72:40
1/6/2020 08:49:43 PM > Wi-Fi MAC address: 64:xxxxx:48:71
1/6/2020 08:49:43 PM > SPC: 304150
1/6/2020 08:49:43 PM > --------------------------------------------------------------------------------
1/6/2020 08:49:43 PM > Reading security area...1/6/2020 08:49:43 PM > OK
1/6/2020 08:49:43 PM > Backup saved to "SP200_3596340xxxxxxx_06-01-2020_20-49-43.EEP"
1/6/2020 08:49:43 PM > --------------------------------------------------------------------------------
1/6/2020 08:49:43 PM > Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones, modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your computer during the flashing!
1/6/2020 08:49:43 PM > --------------------------------------------------------------------------------
1/6/2020 08:49:48 PM > Opening "SP20013b_to_X210ULMA10d_for_unlock.oct"...1/6/2020 08:49:48 PM > OK
1/6/2020 08:49:48 PM > Setting options...1/6/2020 08:49:50 PM > OK
1/6/2020 08:49:50 PM > Selecting firmware partitions...1/6/2020 08:49:53 PM > OK
1/6/2020 08:49:53 PM > Selected default partitions!
1/6/2020 08:49:53 PM > Reading partitions...1/6/2020 08:49:53 PM > OK
1/6/2020 08:49:53 PM > Do you want to format User Data?
1/6/2020 08:50:10 PM > Formating USERDATA...1/6/2020 08:50:14 PM > OK
1/6/2020 08:50:14 PM > Formating ENCRYPT...1/6/2020 08:50:18 PM > OK
1/6/2020 08:50:18 PM > Sending signature...1/6/2020 08:50:19 PM > OK
1/6/2020 08:50:19 PM > Writing preloader...1/6/2020 08:50:22 PM > OK
1/6/2020 08:50:22 PM > Writing pgpt...1/6/2020 08:50:22 PM > OK
1/6/2020 08:50:22 PM > Writing lk...1/6/2020 08:50:23 PM > OK
1/6/2020 08:50:23 PM > Writing lk2...1/6/2020 08:50:23 PM > OK
1/6/2020 08:50:23 PM > Writing laf...1/6/2020 08:50:26 PM > OK
1/6/2020 08:50:26 PM > Writing boot...1/6/2020 08:50:28 PM > OK
1/6/2020 08:50:28 PM > Writing recovery...1/6/2020 08:50:30 PM > OK
1/6/2020 08:50:30 PM > Writing logo...1/6/2020 08:50:30 PM > OK
1/6/2020 08:50:30 PM > Writing lo_bak_go...1/6/2020 08:50:31 PM > OK
1/6/2020 08:50:31 PM > Writing secro...1/6/2020 08:50:31 PM > OK
1/6/2020 08:50:31 PM > Writing tee1...1/6/2020 08:50:31 PM > OK
1/6/2020 08:50:31 PM > Writing tee2...1/6/2020 08:50:31 PM > OK
1/6/2020 08:50:31 PM > Writing rct...1/6/2020 08:50:32 PM > OK
1/6/2020 08:50:32 PM > Writing factory...1/6/2020 08:50:32 PM > OK
1/6/2020 08:50:32 PM > Writing efuse...1/6/2020 08:50:32 PM > OK
1/6/2020 08:50:32 PM > Writing md1img...1/6/2020 08:50:34 PM > OK
1/6/2020 08:50:34 PM > Writing md1dsp...1/6/2020 08:50:34 PM > OK
1/6/2020 08:50:34 PM > Writing md1arm7...1/6/2020 08:50:35 PM > OK
1/6/2020 08:50:35 PM > Writing md3img...1/6/2020 08:50:35 PM > OK
1/6/2020 08:50:35 PM > Writing system...
1/6/2020 08:54:03 PM > Try RCV Msg 0 : 0
1/6/2020 08:58:40 PM > Try RCV Msg 0 : 01/6/2020 08:58:40 PM > OK
1/6/2020 08:58:40 PM > Writing lafbak...1/6/2020 08:58:43 PM > OK
1/6/2020 08:58:43 PM > Writing ftm...1/6/2020 08:58:44 PM > OK
1/6/2020 08:58:44 PM > Writing cache...1/6/2020 08:58:46 PM > OK
1/6/2020 08:58:46 PM > Writing OP...1/6/2020 08:59:06 PM > OK
1/6/2020 08:59:06 PM > Writing userdata...1/6/2020 08:59:41 PM > OK
1/6/2020 08:59:41 PM > Formating RCT...1/6/2020 08:59:45 PM > OK
1/6/2020 08:59:45 PM > Finalizing...1/6/2020 08:59:48 PM > OK
1/6/2020 08:59:48 PM > Performed by 2.9.7.01 Software version.
1/6/2020 08:59:48 PM > Elapsed Time: 12:10:34 AM
Go to the top of the page
 
+Quote Post
A continuacion 2 usuario(s) le Agradece(n) a Andosonson por su Colaboracion:
chinoperez, master2006
Tecnozaza
mensaje Mar 4 2020, 10:57 AM
Publicado: #16

Miembro del Clan
*

Grupo: Miembros
Mensajes: 1
Agradecimientos: 0
Registrado: 3-March 20
Miembro No.: 1,164,849
Pais:cu


[/left]
CITA(Dr Phone´s @ May 8 2019, 02:56 PM) *
Compañeros les comparto mi experencia con el unlock al modelo LG SP200 version 17a parche seguridad Marzo 1, 2019.

NOTA: antes que nada cabe aclarar que los resultados fueron de un proceso de mucha lectura sobre otros post y sobre errores de otros colegas. Fue testeado con la Version 17a pero creeria que si seguien los mismos procesos es funcional para versiones anteriores. Doy credito a quien dio inicio con esto en el clan Arturo1971 y a los colegas que comentan sus experiencias en el siguiente Link https://www.clangsm.com/forum/index.php?showtopic=509736 y a los link encontrados.

IMPORTANTE: Al momento de iniciar con la instalacion del firmware y que de ERROR, NO DESCONECTAR BATERIA, solamente retirar cable y seguir insistiendo con la instalacion de Firmware en Octoplus, hasta que termine el proceso. BATERIA con un 90% de carga para evitar problemas.

PASO 1: Realizar lectura de Eproom con Octoplus seleccionando modelo SP200

PASO 2: Cargar firmware SP20013b_to_X210ULMA10d_for_unlock.oct con Octoplus
En este proceso nos dira que no es del modelo exacto, damos que si, todos los archivos seleccionados del firmware los dejamos, nos dira si necesitamos dar Formato UserData, damos que si
en mi caso aca empezo a dar error, SIN REMOVER BATERIA solo cable, volvi a realizar el mismo proceso cuando pedia conectar sin necesidad de precionar vol+ porque ya esta en modo Descarga
solo conectamos y continua el proceso, si vuelve a dar error en algun paso continuar haciendo lo mismo, hasta que nos diga OK todo el proceso.

Fichero Adjunto  SP20017a... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 186.69k ) Número de descargas: 0


Fichero Adjunto  error_sp... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 169.45k ) Número de descargas: 0


Fichero Adjunto  Firmware... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 169.36k ) Número de descargas: 0


En este momento el teléfono ya nos enciende como K8+, en mi caso quedo freezado en el logo no preocuparse, realice un hard reset desde recovery (por si a alguno le funciona con esto) en lo personal continuo el telefono en el logo, no preocupars, continuar con el siguiente paso.

PASO 3: Carga de Firmware desde LG-UP solucionando problema de logo en pantalla
Una vez descargado el Archivo LG-UP descomprimir e instalarlo, para que les funcione sin problema deben sustituir los archivos LGUP.exe y MODEL a la carpeta donde se realizo la instalación en el disco C en mi caso fue a la siguiente direccion... C:\Program Files\LG Electronics\LGUP

Habiendo realizado esto, abren programa LG-UP y conectan el telefono en modo Download (vol+ por 10 seg y conectar usb) seleccionan la opcion CHIPERASE y en archivo BIN seleccionan el que dejo en el archivo SP200.kdz encontrado en la red, proceden a dar Start y al terminar el proceso el telefono enciende Normal.

Fichero Adjunto  Proceso_... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 64.34k ) Número de descargas: 0


PASO 4: Cargar Archivo Eproom leido en paso 1 y LISTO telefono funcionando smile.gif

PD. Esta fue la forma en que yo lo realice, quiza puedan saltarse el paso del primer Firmware unlock.oct y colocar Firmware X210 a la primera, pero seria bajo su riesgo, Comenten Resultados smile.gif

Fichero Adjunto  Unlock_S... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 388bytes ) Número de descargas: 143

[indent][/indent][left]
Go to the top of the page
 
+Quote Post
cibermovil
mensaje Apr 7 2020, 01:14 PM
Publicado: #17

Miembro del Clan
*

Grupo: Miembros
Mensajes: 78
Agradecimientos: 243
Registrado: 3-May 10
Miembro No.: 101,066



CITA(Dr Phone´s @ May 8 2019, 01:56 PM) *
Compañeros les comparto mi experencia con el unlock al modelo LG SP200 version 17a parche seguridad Marzo 1, 2019.

NOTA: antes que nada cabe aclarar que los resultados fueron de un proceso de mucha lectura sobre otros post y sobre errores de otros colegas. Fue testeado con la Version 17a pero creeria que si seguien los mismos procesos es funcional para versiones anteriores. Doy credito a quien dio inicio con esto en el clan Arturo1971 y a los colegas que comentan sus experiencias en el siguiente Link https://www.clangsm.com/forum/index.php?showtopic=509736 y a los link encontrados.

IMPORTANTE: Al momento de iniciar con la instalacion del firmware y que de ERROR, NO DESCONECTAR BATERIA, solamente retirar cable y seguir insistiendo con la instalacion de Firmware en Octoplus, hasta que termine el proceso. BATERIA con un 90% de carga para evitar problemas.

PASO 1: Realizar lectura de Eproom con Octoplus seleccionando modelo SP200

PASO 2: Cargar firmware SP20013b_to_X210ULMA10d_for_unlock.oct con Octoplus
En este proceso nos dira que no es del modelo exacto, damos que si, todos los archivos seleccionados del firmware los dejamos, nos dira si necesitamos dar Formato UserData, damos que si
en mi caso aca empezo a dar error, SIN REMOVER BATERIA solo cable, volvi a realizar el mismo proceso cuando pedia conectar sin necesidad de precionar vol+ porque ya esta en modo Descarga
solo conectamos y continua el proceso, si vuelve a dar error en algun paso continuar haciendo lo mismo, hasta que nos diga OK todo el proceso.

Fichero Adjunto  SP20017a... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 186.69k ) Número de descargas: 0


Fichero Adjunto  error_sp... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 169.45k ) Número de descargas: 0


Fichero Adjunto  Firmware... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 169.36k ) Número de descargas: 0


En este momento el teléfono ya nos enciende como K8+, en mi caso quedo freezado en el logo no preocuparse, realice un hard reset desde recovery (por si a alguno le funciona con esto) en lo personal continuo el telefono en el logo, no preocupars, continuar con el siguiente paso.

PASO 3: Carga de Firmware desde LG-UP solucionando problema de logo en pantalla
Una vez descargado el Archivo LG-UP descomprimir e instalarlo, para que les funcione sin problema deben sustituir los archivos LGUP.exe y MODEL a la carpeta donde se realizo la instalación en el disco C en mi caso fue a la siguiente direccion... C:\Program Files\LG Electronics\LGUP

Habiendo realizado esto, abren programa LG-UP y conectan el telefono en modo Download (vol+ por 10 seg y conectar usb) seleccionan la opcion CHIPERASE y en archivo BIN seleccionan el que dejo en el archivo SP200.kdz encontrado en la red, proceden a dar Start y al terminar el proceso el telefono enciende Normal.

Fichero Adjunto  Proceso_... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 64.34k ) Número de descargas: 0


PASO 4: Cargar Archivo Eproom leido en paso 1 y LISTO telefono funcionando smile.gif

PD. Esta fue la forma en que yo lo realice, quiza puedan saltarse el paso del primer Firmware unlock.oct y colocar Firmware X210 a la primera, pero seria bajo su riesgo, Comenten Resultados smile.gif

Fichero Adjunto  Unlock_S... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 388bytes ) Número de descargas: 143






me quedó, solo con la flash for unlock que hay en el servidor de octoplus, solo hizé un hard reset previo al flash.
Go to the top of the page
 
+Quote Post
vibcellular
mensaje May 1 2020, 05:37 PM
Publicado: #18

Miembro del Clan
*

Grupo: Miembros
Mensajes: 77
Agradecimientos: 64
Registrado: 6-February 15
Desde: la ceiba
Miembro No.: 685,672



CITA(Rubso @ Aug 14 2019, 06:44 PM) *
Acabo de sacar uno con la version SP20018b con el metodo pasado y sin ningun problema de pantalla corrida

1.- Read EEPROM
2.- Write firmware: X210ULMA10d (hard Reset)
3.- Write EEPROM (hard Reset
4.- Listo

Welcome to Octoplus/Octopus Box LG Software version 2.9.3
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LG-SP200
Platform: mt6750
Android version: 7.1.2
SW version: SP20018b_01
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 351980-09-016630-5
MEID: 351980-09-016630
Bluetooth address: B4:F7:A1:2D:67:37
Wi-Fi MAC address: B4:F7:A1:D6:3C:F6
SPC: 894141
--------------------------------------------------------------------------------
Selecting output file...OK
Destination file: "SP200_35198009016630_14-08-2019_17-15-20.EEP"
Reading EEPROM...OK
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG Qualcomm
Selected port: COM34
Selected model: MS428
Reading info...
Model ID: LG-SP200
Incompatible model ID!
IMEI:
Android version:
Battery level: 50%
Mode: Emergency
Initializing flash...OK
Platform: mt6750
SW version: SP20018b_01
Android version: 7.1.2
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
--------------------------------------------------------------------------------
Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones,
modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any
installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your
computer during the flashing!
--------------------------------------------------------------------------------
Opening "SP200.oct"...OK
Selecting firmware partitions...OK
Selected default partitions!
Setting options...OK
Do you want to format User Data?
Reading partitions...OK
Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing preloader...OK
Writing pgpt...OK
Writing lk...OK
Writing lk2...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing logo...OK
Writing lo_bak_go...OK
Writing secro...OK
Writing tee1...OK
Writing tee2...OK
Writing factory...OK
Writing efuse...OK
Writing md1img...OK
Writing md1dsp...OK
Writing md1arm7...OK
Writing md3img...OK
Writing system...OK
Writing lafbak...OK
Writing sgpt...OK
Writing ftm...OK
Writing cache...OK
Writing OP...OK
Writing userdata...OK
Reading partitions...OK
Formating RCT...OK
Formating MPT...OK
Finalizing...OK
Writing firmware done!
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LM-X210ULMA
Platform: mt6750
Android version: 7.1.2
SW version: LMX210ULMAAT-00-V10d-LAO-COM-MAR-16-2018-ARB00+
0
LAF Version: 1.1
Product ID: 00000000000000000000000000000
IMEI:
Target operator: LAO
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 350305-26-000000-1
MEID: 350305-26-000000
Bluetooth address: 00:05:C9:00:00:00
Wi-Fi MAC address: 00:00:00:00:00:00
SPC: 000000
--------------------------------------------------------------------------------
Detecting writing method...
LAF Error: 80000121.
Trying second method...
Trying third method...Failed!
Trying third method...OK
Opening "SP200_35198009016630_14-08-2019_17-15-20.eep"...OK
Writing EEPROM...OK
EEPROM succesfully repaired.
Performed by 2.9.3 Software version.

Welcome to Octoplus/Octopus Box LG Software version 2.9.3
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LG-SP200
Platform: mt6750
Android version: 7.1.2
SW version: SP20018b_01
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 351980-09-016630-5
MEID: 351980-09-016630
Bluetooth address: B4:F7:A1:2D:67:37
Wi-Fi MAC address: B4:F7:A1:D6:3C:F6
SPC: 894141
--------------------------------------------------------------------------------
Selecting output file...OK
Destination file: "SP200_35198009016630_14-08-2019_17-15-20.EEP"
Reading EEPROM...OK
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG Qualcomm
Selected port: COM34
Selected model: MS428
Reading info...
Model ID: LG-SP200
Incompatible model ID!
IMEI:
Android version:
Battery level: 50%
Mode: Emergency
Initializing flash...OK
Platform: mt6750
SW version: SP20018b_01
Android version: 7.1.2
LAF Version: 1.1
Product ID: CT69S171208005881
IMEI:
Target operator: SPR
Hardware: rev_10
--------------------------------------------------------------------------------
Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones,
modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any
installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your
computer during the flashing!
--------------------------------------------------------------------------------
Opening "SP200.oct"...OK
Selecting firmware partitions...OK
Selected default partitions!
Setting options...OK
Do you want to format User Data?
Reading partitions...OK
Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing preloader...OK
Writing pgpt...OK
Writing lk...OK
Writing lk2...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing logo...OK
Writing lo_bak_go...OK
Writing secro...OK
Writing tee1...OK
Writing tee2...OK
Writing factory...OK
Writing efuse...OK
Writing md1img...OK
Writing md1dsp...OK
Writing md1arm7...OK
Writing md3img...OK
Writing system...OK
Writing lafbak...OK
Writing sgpt...OK
Writing ftm...OK
Writing cache...OK
Writing OP...OK
Writing userdata...OK
Reading partitions...OK
Formating RCT...OK
Formating MPT...OK
Finalizing...OK
Writing firmware done!
Performed by 2.9.3 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM34
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM34
Mode: Emergency
Initializing flash...OK
Model ID: LM-X210ULMA
Platform: mt6750
Android version: 7.1.2
SW version: LMX210ULMAAT-00-V10d-LAO-COM-MAR-16-2018-ARB00+
0
LAF Version: 1.1
Product ID: 00000000000000000000000000000
IMEI:
Target operator: LAO
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI: 350305-26-000000-1
MEID: 350305-26-000000
Bluetooth address: 00:05:C9:00:00:00
Wi-Fi MAC address: 00:00:00:00:00:00
SPC: 000000
--------------------------------------------------------------------------------
Detecting writing method...
LAF Error: 80000121.
Trying second method...
Trying third method...Failed!
Trying third method...OK
Opening "SP200_35198009016630_14-08-2019_17-15-20.eep"...OK
Writing EEPROM...OK
EEPROM succesfully repaired.
Performed by 2.9.3 Software version.


FUNCIONA FULL muchas gracias!!
Go to the top of the page
 
+Quote Post
daniicordova
mensaje Oct 9 2020, 03:04 PM
Publicado: #19

Miembro del Clan
*

Grupo: Miembros
Mensajes: 17
Agradecimientos: 62
Registrado: 20-April 16
Miembro No.: 820,542
Pais:mx


CITA(VICTORRAV @ Oct 17 2019, 06:14 PM) *
100% full con version 19a


compañero, para la version 19a, ¿como lo realizaste? buen dia.
Go to the top of the page
 
+Quote Post
CCASTILLO
mensaje Nov 16 2020, 12:42 PM
Publicado: #20

Miembro del Clan
*

Grupo: Miembros
Mensajes: 56
Agradecimientos: 75
Registrado: 25-December 10
Miembro No.: 164,425



PASEN POR AKI

https://www.clangsm.com/forum/index.php?s=&...t&p=1996991
Go to the top of the page
 
+Quote Post

2 Páginas: V   1 2 >
Reply to this topicStart new topic
1 usuario(s) está(n) leyendo este tema (1 invitado(s) y 0 usuario(s) anónimo(s))
0 usuarios(s) registrado(s):

 



Ver Visitas Fecha y Hora actual: 28th March 2024 - 06:47 AM
►Reglamento      ►Política de Privacidad
Este sitio web usa cookies, puedes ver la política de cookies, aquí -
Política de cookies +