Actualizaciones De La Riff Box Solo Aqui Opciones

[yago98]

RIFF JTAG – Samsung Galaxy S 4G (T959v 1GB) Unbrick – Boot repair supported

22.06.2011 Samsung Galaxy S 4G (T959v 1GB) Unbrick – Boot repair supported

Samsung T959V is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung T959V:

•Solder JTAG cable to Samsung T959V JTAG pads;
•Connect microUSB cable to phone and PC;
•Insert battery;
•Make sure Samsung T959V is selected in the list of models;
•Make sure a fixed TCK frequency is selected;
•Click Resurrect button;
•Wait till software signals a successful operation completion;
•Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

•Disconnect PC cable;
•Insert battery;
•Hold both ‘Volume Down’ and ‘Volume Up’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[Anunciante Autorizado]

[dapx]

RIFF JTAG - HTC Wildfire S A510E (HTC Marvel), 7 More CDMA models supported

07.07.2011 HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.


Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC WildFireS:

Solder JTAG cable to HTC WildFireS JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC WildFireS is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:

Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.




Following CDMA models are supported from today :



Samsung B139 Repair/Unbrick, Read/Write NOR Flash
Samsung B259 Repair/Unbrick, Read/Write NOR Flash
Samsung B309 Repair/Unbrick, Read/Write NOR Flash
Samsung B319 Repair/Unbrick, Read/Write NOR Flash
Samsung B379 Repair/Unbrick, Read/Write NOR Flash
Samsung B619 Repair/Unbrick, Read/Write NOR Flash
Huawei C31 Repair, Read/Write NOR flash

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Saludos. Enjoy

[3zr3vnoc]

RIFF JTAG - Samsung T749, Samsung E189 Unbrick - Boot repair supported

12.07.2011 Samsung T749, Samsung E189 Unbrick – Boot repair supported

The Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung T749:

Solder JTAG cable to Samsung T749 JTAG pads;
Connect USB cable;
Make sure Samsung T749 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.



Resurrecting Samsung E189 is simple.

Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256

To resurrect Samsung E189:

Solder JTAG cable to Samsung E189 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Samsung E189 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;



Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[3zr3vnoc]

RIFF JTAG - Latest Updates and News !

Here is short list of latest news :

RIFF JTAG – Qtek 9000 (HTC Universal) Unbrick – Boot repair supported « RIFF Box – JTAG Revolution

Other names for this device :

I-Mate JASJAR (HTC Universal)


Dopod 900 (HTC Universal)


O2 XDA Exec (HTC Universal)


T-Mobile MDA Pro (HTC Universal)


Orange SPV M5000 (HTC Universal)


Qtek 9000 (HTC Universal)


Grundig GR980 (HTC Universal)


Vodafone VPA IV / v1640 (HTC Universal)


Bug fix updates :


HTC_Wildfire.dll

- Added feature to flash RECOVERY and BOOT zones during resurrection.
- Added code reading option
HTC_WildfireS.dll
- By mistake was released DLL for usual HTC Wildfire model. Now is ok.

Thanks to Tatek and Basar for help. Free beers for both
Qualcomm Partition tool 1.04 :


Added support for 4kb page code reading (Applies to HTC Models)
In case You want to read unlock code from dump with 4kb page, and You get "Simlock zone is not found" message, tick "Don't adjust HTC Partition for 4kb NAND pages" check box, and read partition again.

Beta testers required for Samsung Galaxy S II :

Support for Exynos 4210 Samsung CPU is added, and will be released after tests.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[SpLock]

RIFF JTAG - Samsung GT-i8700 Omnia 7 , Samsung W299 Duos Unbrick - Boot repair suppor

29.07.2011 Samsung GT-i8700 Omnia 7 , Samsung W299 Duos Unbrick – Boot repair supported


Resurrecting Samsung I8700 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.

To resurrect Samsung I8700:

Solder JTAG cable to Samsung I8700 JTAG pads;
Make sure Samsung I8700 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button. In few seconds phone enters download mode.




Resurrecting Samsung W299 is simple. Phone is auto powered on with USB Data Cable connected to the PC while battery is inside. In case you use the battery only please note you will have to press Power On key once.


To resurrect Samsung W299:

Solder JTAG cable to Samsung W299 JTAG pads;
Make sure Samsung W299 is selected in the list of models;
Insert Battery into phone and connect USB cable (in case you not use USB cable, press once the Power ON key on the phone)
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.




Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[dapx]

Booooommmm

RIFF JTAG – Samsung I9100 Galaxy S II Unbrick – Boot repair supported, World First ! ! !


by admin on Jul.29, 2011, under News

29.07.2011 Samsung I9100 Galaxy S II Unbrick – Boot repair supported, World First ! ! !

Samsung I9100 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core).

JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the OMAP4430 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Phone has such booting sequence: ROM → FBL → IBL → PBL → SBL. Current resurrector will resurrect Partition Table (PIT) and SBL zones which are located in the iNAND (eMMC) memory. Write access to memory which contains FBL, IBL and PBL loaders is not supported currently, but in case your phone has these loaders damaged, you can choose “Initiate Download Mode” way of resurrection in order to directly put the phone into the Download Mode.

To resurrect Samsung I9100:

Solder JTAG cable to Samsung I9100 JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung I9100 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF JTAG -Samsung Galaxy S II Unbrick Support and much more !
29.07.2011 New RIFF JTAG Updates :

- RIFF JTAG Manager v1.34
- RIFF Box firmware v1.26
- RIFF GDB Server v1.04

With new release we added support for new ARM core(s) - Cortex-A9 in single core and multicore configuration.

Project now supports Unicode, so there is Russian and Chinese language available !

JTAG Manager now supports 64bit addressing, thus allowing You to dump large memory chips (eMMC and iNAND) !

New resurrectors DLL-s


- Samsung Galaxy S II (Samsung i9100) Unbrick, Boot repair
- SonyEricsson x10 Unbrick, Boot repair
- Samsung CDMA B119

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Saludos. Enjoy

Mensaje modificado por dapx el Jul 29 2011, 12:14 PM

[SpLock]

RIFF JTAG -Samsung Galaxy S II Unbrick Support and much more !

29.07.2011 New RIFF JTAG Updates :

- RIFF JTAG Manager v1.34 - RIFF Box firmware v1.26 - RIFF GDB Server v1.04

With new release we added support for new ARM core(s) - Cortex-A9 in single core and multicore configuration.

Project now supports Unicode, so there is Russian and Chinese language available !

JTAG Manager now supports 64bit addressing, thus allowing You to dump large memory chips (eMMC and iNAND) !

New resurrectors DLL-s

- Samsung Galaxy S II (Samsung i9100) Unbrick, Boot repair
- SonyEricsson x10 Unbrick, Boot repair
- Samsung CDMA B119

http://www.jtagbox.com/.

[jhon357add]

30.07.2011 SonyEricsson Xperia X10 Unbrick – Boot repair supported

Resurrecting SE X10 is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is inserted. Be careful, JTAG pads are covered under blue mask covering, so you will need to scratch it off in order to be able to solder wires.
During resurrection, you can select which areas to be repaired. So you can choose only those areas which you know are damaged thus saving flashing time.

To resurrect SE X10:

* Solder JTAG cable to SE X10 JTAG pads;
* Insert USB Data cable into board and PC;
* Make sure SE X10 is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.

[miguelpaolo]

02.08.2011 RIFF JTAG - SonyEricsson Xperia X8, X10 Mini supported

SonyEricsson Xperia X8/E15 Unbrick, Boot repair, and NAND Chip Backup/Restore
SonnyEricsson Xperia X10a Mini /E10 Unbrick, Boot repair, and NAND Chip Backup/Restore
USB Broadband Modem ZTE MF627 new CPU ID added to allowed list


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[jhon357add]

03.08.2011 Samsung Galaxy Tab M180s Unbrick – Boot Repair supported

Samsung M180S is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.

To resurrect Samsung M180S:

* Solder JTAG cable to Samsung M180S JTAG pads;
* Connect USB cable to phone and PC;
* Attach battery connector;
* Make sure Samsung M180S is selected in the list of models;
* Make sure a fixed TCK frequency is selected;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.

To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

[jhon357add]

04.08.2011 JTAG Manager v1.35 released

Whats new:

* Added an arbitrary feature “Settings by Code” to the DCC Read/Write page.

Main purpose is to improve support quality for users: via “Settings Code” string a supporter person sees all settings which were set by user on the DCC Read/Write page.
Though, end-user may benefit from this too: Use “Settings Code” string for JTAG Manager to automatically setup all DCC Read/Write settings

* Fixed data loss during read and save operations in case there is not enough disk space available to store required amount of data.

(for example reading full on DCC Read/Write page, or saving read full, etc).
Now available disk space checks are performed prior disk write operations.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[MacSE]

RIFF JTAG - Samsung Galaxy GIO (S5660) Unbrick - Boot repair supported

23.08.2011 Samsung Galaxy GIO (S5660) Unbrick – Boot repair supported

Samsung S5660 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


To resurrect Samsung S5660 do this:

Solder JTAG cable to Samsung S5660 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung S5660 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;




Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[jhon357add]

RIFF JTAG – HTC Wizard 200 Unbrick – Boot repair supported

by admin on Aug.25, 2011, under News

25.08.2011 HTC Wizard 200 Unbrick – Boot repair supported

Resurrection of HTC Wizard 200 is simple. Battery must be connected in order to establish JTAG connection.
Current resurrector works with devices based on G4 MDOC chip.
Resurrector can repair IPL and SPL areas (which areas to repair you can select in popup window).
Please note: DiskOnChip G4 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the IPL area. Thus be very carefull not to interrupt IPL repair process (in case you have selected IPL area to be repaired).
In case your device has permanently blocked MDOC memory you will see this error:

****************************************************************
Detected a Not Initialized FLASH1 Chip ID: 0×0400/0xFBFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
****************************************************************
This can happen due to unknown protection keys used or due to permanently blocked MDOC chip. If latter is true we advise you to solder a new flash memory chip or throw this phone away to the trash bin.
To resurrect HTC Wizard:

* Solder JTAG cable to HTC Wizard JTAG pads;
* Insert battery and connect USB cable to phone and PC;
* Make sure HTC Wizard is selected in the list of models;
* Press Power On key
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ‘Camera’ key and press ‘Power ON’ button.

[dapx]

RIFF JTAG - 7 new models added - read inside !
30.08.2011 RIFF JTAG - 7 new models added !

Whats new :

LG Models :
LG GM730
LG TD636
Samsung :
Samsung i5510
Samsung A837
Sierra Wireless
Sierra 597 Compass
Sierra U595
Pantech :
Pantech UM150



Please click "Check For Updates" button in order to download and apply new updates.

Saludos. Enjoy

[jhon357add]

RIFF JTAG – HTC Desire S S510E (HTC Saga) – Unbrick, Unlock, CID, IMEI Update supported

by admin on Sep.09, 2011, under News

09.09.2011 HTC Desire S S510E (HTC Saga) – Unbrick, Unlock, CID, IMEI Update supported
Resurrecting HTC Desire S is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
Some (or all) revisions of HTC Desire S boards have JTAG interface disabled (that is enable MARM JTAG Fuse is blown in the MSM8255 chip). In this case the JTAG may be enabled only by firmware itself. This is done by the FSBL loader, so writing to FSBL area is artificially disabled in the DCC Loader code. DCC Loader will discard all flashing attempts into FSBL zone and will respond with success code as if flashing succeeded. In this way FSBL zone is protected while user still can flash full image files seamlessly.
Resurrector will reflash radio’s boot zone (except FSBL area) and will re-write PDA’s SPL to 0.98.0000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PG8810000’.
There is option to reflash BOOT and RECOVERY zones.
Please note, if your phone has the FSBL loader damaged and MCU has JTAG FUSE blown then there is no way to resurrect your phone via JTAG interface.
To resurrect HTC Desire S:

* Solder JTAG cable to HTC Desire S JTAG pads;
* Insert batter and connect USB Data cable;
* Make sure HTC Desire S is selected in the list of models;
* If you use only battery, press Power On key;
* Click Resurrect button;
* Wait till software signals a successful operation completion;
* Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:

* Disconnect PC cable;
* Insert battery;
* Hold ‘Volume Down’ key and press ‘Power ON’ button.

[SpLock]

RIFF JTAG - New Samsung and CDMA updates !
30.09.2011 RIFF JTAG - New Samsung and CDMA updates !

Whats new :

• Added support for Samsung AnyCall m110s
• Added support for Samsung Wave II (S8530)
• Added support for Sungil SXC1080 CDMA Modem

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

RIFF Box – JTAG Revolution

[SpLock]

RIFF JTAG - Samsung and CDMA updates !

03.10.2011 RIFF JTAG - Samsung and CDMA updates !

Whats new :

Added support for Samsung B209

Added support for Samsung S7330 Unbrick

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files

RIFF Box – JTAG Revolution

[SpLock]

RIFF JTAG - Samsung updates !

04.10.2011 Samsung Focus (i917) Unbrick, Dead boot repair supported

Added support for Samsung Focus (i917) Unbrick

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

RIFF Box – JTAG Revolution

[Jhonny]

RIFF JTAG - Samsung updates !

04.10.2011 Samsung Focus (i917) Unbrick, Dead boot repair supported

Added support for Samsung Focus (i917) Unbrick

Please click "Check for Updates" Button in RIFF JTAG Manager to download and install new files.

RIFF Box – JTAG Revolution

Traducción:

RIFF JTAG - actualizaciones de Samsung

04/10/2011 Samsung Focus (i917) unbrick, reparación del boot muerto apoyado

Añadido soporte para Samsung Focus (i917) unbrick

Por favor, haga clic en "Buscar actualizaciones" botón de Administrador de RIFF JTAG para descargar e instalar los nuevos archivos.

Caja RIFF - JTAG Revolución...!!

[SpLock]

JTAG Manager Version 1.36, RIFF Box Firmware v1.27 Released,Tegra 2 Support ! ! !


- added fast presets for automatic selection of settings for most common operations on DCC Read/Write page
For this click Settings by Code button and select a desired preset from list and then click Apply Settings.
For example if user selects "Write Full Image into NAND memory" the valid settings on the DCC Read/Write page
for writting full images into devices with NAND memory will be automatically selected
- fixed serious bug which caused resurrector DLLs which do upload data into RAM to upload broken data
For example DLLs which start Downlad Mode directly use this feature.
- added feature to accept text name of memory chip from DCC Loader and display it (currently used to display eMMC memory product name)
- fixed bug for resumming interrupted DCC Read: ifvcurrently cached file size was greater than > 2GB
(that is if read was interrupted on point when there was already more than 2GB of data read) the new reading data was not appended to the readout file end, but instead the file was corrupted.
- fixed bug for saving big files (after reading on DCC Read/Write page): if size exceeded 0x7FFFFFFF bytes JTAG Manager show no free disk space error.
- added TEGRA2 chipset selection in the Target list
- fixed an issue with the resurrection progress bar: in some cases during resurrection operations the progress bar would always stay at 0%.


Firmware 1.27
---------------------------
- added TEGRA2 debugging support (dual-core Cortex-A9)
- added new breakpoint type: "address mismatch" which allows geniune single-stepping on Cortex-A8,A9 (CoreSight) targets
(thus GDB Server can now perform low-level single step commands)