Unlock Sp200 100% Seguro Y Real En La Version 14c!!!! Opciones

[alexvlasova]

Sencillo. Usar la flash en formato .OCT que esta posteada en el forum de Arturo1971
No necesite factory reset o ningun otro programa de LG.
Solo Octo
100% funcional.
No hubo problemas de ningun tipo
NO Z3X
No convertir
No bootloop, no pantalla corrida, no nada
Octoplus arreglo el procedimiento de flasheo para este modelo junto con el firmware posteado

Solo con estos pasos

1. Solo seleccionar el modelo SP200
2. Hacer un Backup de la EEPROM
3. Luego seleccionar la flash SP20013b_to_X210ULMA10d_for_unlock.oct
4. Flashear el equipo. Luego de terminar no dejar iniciar, solo quitar la bateria y poner en modo download nuevamente
5. Flashear la EEPROM Backup
6. Iniciar normalmente
La flash la pueden descargar desde el post de Arturo1971
https://www.clangsm.com/forum/index.php?act...t&id=306319
O del link de OctoplusTeam en googledrive
ver txt


Este es el log
Welcome to Octoplus/Octopus Box LG Software version 2.9.1
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM11
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM9
Mode: Emergency
Initializing flash...OK
Model ID: LG-SP200
Platform: mt6750
Android version: 7.1.2
SW version: SP20014c_00
LAF Version: 1.1
Product ID:
IMEI:
Target operator: SPR
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI:
MEID:
Bluetooth address:
Wi-Fi MAC address:
SPC:
-------------------------------------------------------------------------------
Reading security area...OK
Backup saved to "XXX.EEP"
--------------------------------------------------------------------------------
Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones,
modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any
installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your
computer during the flashing!
--------------------------------------------------------------------------------
Opening "SP20013b_to_X210ULMA10d_for_unlock.oct"...OK
Setting options...OK
Selecting firmware partitions...OK
Selected default partitions!
Reading partitions...OK
Do you want to format User Data?
Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing preloader...OK
Writing pgpt...OK
Writing lk...OK
Writing lk2...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing logo...OK
Writing lo_bak_go...OK
Writing secro...OK
Writing tee1...OK
Writing tee2...OK
Writing rct...OK
Writing factory...OK
Writing efuse...OK
Writing md1img...OK
Writing md1dsp...OK
Writing md1arm7...OK
Writing md3img...OK
Writing system...OK
Writing lafbak...OK
Writing ftm...OK
Writing cache...OK
Writing OP...OK
Writing userdata...OK
Formating RCT...OK
Finalizing...OK
Performed by 2.9.1 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM11
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.

Phone found at port COM9
Mode: Emergency
Initializing flash...OK
Model ID: LM-X210ULMA
Platform: mt6750
Android version: 7.1.2
SW version:
LAF Version: 1.1
Product ID:
IMEI:
Target operator: LAO
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...Failed!
--------------------------------------------------------------------------------
IMEI:
MEID: Bad
Bluetooth address: Unknown
Wi-Fi MAC address: Unknown
--------------------------------------------------------------------------------
Detecting writing method...
LAF Error: 80000121.
Trying second method...
Trying third method...Failed!
Trying third method...OK
Opening "XXX.eep"...OK
Writing EEPROM...OK
EEPROM succesfully repaired.
Performed by 2.9.1 Software version.

Mensaje modificado por alexvlasova el Feb 24 2019, 07:52 PM

Fichero(s) Adjunto(s)

 link.txt... Usted aun no cumple los requisitos para descargar archivos. CLICK para mas INFO ( 93bytes ) Número de descargas: 71

 

[Anunciante Autorizado]

[randolfotecnicom]

Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing preloader...OK
Writing pgpt...OK
Writing lk...OK
Writing lk2...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing logo...OK
Writing lo_bak_go...OK
Writing secro...OK
Writing tee1...OK
Writing tee2...OK
Writing rct...OK
Writing factory...OK
Writing efuse...OK
Writing md1img...OK
Writing md1dsp...OK
Writing md1arm7...OK
Writing md3img...OK
Writing system...Failed!
Performed by 2.9.4 Software version.

siempre me da error en esa parte.

[reynaldotellez]

Sencillo. Usar la flash en formato .OCT que esta posteada en el forum de Arturo1971
No necesite factory reset o ningun otro programa de LG.
Solo Octo
100% funcional.
No hubo problemas de ningun tipo
NO Z3X
No convertir
No bootloop, no pantalla corrida, no nada
Octoplus arreglo el procedimiento de flasheo para este modelo junto con el firmware posteado

Solo con estos pasos

1. Solo seleccionar el modelo SP200
2. Hacer un Backup de la EEPROM
3. Luego seleccionar la flash SP20013b_to_X210ULMA10d_for_unlock.oct
4. Flashear el equipo. Luego de terminar no dejar iniciar, solo quitar la bateria y poner en modo download nuevamente
5. Flashear la EEPROM Backup
6. Iniciar normalmente
La flash la pueden descargar desde el post de Arturo1971
https://www.clangsm.com/forum/index.php?act...t&id=306319
O del link de OctoplusTeam en googledrive
ver txt
Este es el log
Welcome to Octoplus/Octopus Box LG Software version 2.9.1
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM11
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.
Phone found at port COM9
Mode: Emergency
Initializing flash...OK
Model ID: LG-SP200
Platform: mt6750
Android version: 7.1.2
SW version: SP20014c_00
LAF Version: 1.1
Product ID:
IMEI:
Target operator: SPR
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...
Checking security passed!
--------------------------------------------------------------------------------
IMEI:
MEID:
Bluetooth address:
Wi-Fi MAC address:
SPC:
-------------------------------------------------------------------------------
Reading security area...OK
Backup saved to "XXX.EEP"
--------------------------------------------------------------------------------
Writing phone firmware without real necessity is at your own risk.

Downgrade may lead to phone damage!

Please, make sure the phone's battery is fully charged.
Disconnect all other devices from the computer (including phones,
modems, etc.) and close all other running programs.
To avoid errors in the flashing process, use a clean PC (without any
installed drivers for other Qualcomm-based devices).
You should not run any other programs or attach new devices to your
computer during the flashing!
--------------------------------------------------------------------------------
Opening "SP20013b_to_X210ULMA10d_for_unlock.oct"...OK
Setting options...OK
Selecting firmware partitions...OK
Selected default partitions!
Reading partitions...OK
Do you want to format User Data?
Formating USERDATA...OK
Formating ENCRYPT...OK
Sending signature...OK
Writing preloader...OK
Writing pgpt...OK
Writing lk...OK
Writing lk2...OK
Writing laf...OK
Writing boot...OK
Writing recovery...OK
Writing logo...OK
Writing lo_bak_go...OK
Writing secro...OK
Writing tee1...OK
Writing tee2...OK
Writing rct...OK
Writing factory...OK
Writing efuse...OK
Writing md1img...OK
Writing md1dsp...OK
Writing md1arm7...OK
Writing md3img...OK
Writing system...OK
Writing lafbak...OK
Writing ftm...OK
Writing cache...OK
Writing OP...OK
Writing userdata...OK
Formating RCT...OK
Finalizing...OK
Performed by 2.9.1 Software version.
--------------------------------------------------------------------------------
Checking data...OK
Platform: LG MTK
Selected port: COM11
Selected baudrate: 921600
Selected model: SP200
Selected USB connection type
Please, disconnect cable, reconnect battery, connect P999 cable (with
910k resistor)
or
Reconnect battery, press and hold "Vol+" for 10 seconds and connect
Micro USB cable.

Phone found at port COM9
Mode: Emergency
Initializing flash...OK
Model ID: LM-X210ULMA
Platform: mt6750
Android version: 7.1.2
SW version:
LAF Version: 1.1
Product ID:
IMEI:
Target operator: LAO
Hardware: rev_10
Battery level: 50%
Reading partitions...OK
Checking security...Failed!
--------------------------------------------------------------------------------
IMEI:
MEID: Bad
Bluetooth address: Unknown
Wi-Fi MAC address: Unknown
--------------------------------------------------------------------------------
Detecting writing method...
LAF Error: 80000121.
Trying second method...
Trying third method...Failed!
Trying third method...OK
Opening "XXX.eep"...OK
Writing EEPROM...OK
EEPROM succesfully repaired.
Performed by 2.9.1 Software version.

Amigo, puede verificar el link, a mi no me da error
Saludos de Cuba y gracias por el aporte